• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Change a Subaru Spare Key

If you've lost your Subaru car key, you should call a locksmith. Usually, they can cut an alternative key for you at a lower cost than the dealer.

Subaru car keys are typically either intelligent "push-to-start" fob remote keys, or simply metal keys. The Fob key needs to have its chip changed.

Keyless Entry System

A key fob can be used to lock or unlock your subaru impreza key from a distance and can even open the trunk or lift gate of your vehicle. These remotes are connected to keys inside your car to connect to the computer system of your vehicle.

Subaru models include a less well-known feature called PIN Code Access. You can choose a personal number sequence to open and start your vehicle. Check your owner's guide to learn how to utilize this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

It's likely that the battery inside the key fob has failed. The first thing you'll need to do is ensure that it's got new batteries and you can accomplish this with a portable remote tester or a basic multimeter that you can find in your garage at home.

The next step is to take the key fob out of its case and examine its circuit board for the transmitter. You'll see one or two sets of 8 numbers. Note the first set so you can remember it. After you've completed that take the key fob back together and you'll be ready to start programming it at home. This procedure is different based on the year and model of your car. However, it's generally easy enough to do yourself.

Key Fobs

Subaru's most recent models include key fobs which not only unlock doors, but also turn on lights, lock gas cap, and even start the car. This last trick is particularly beneficial if your experience includes arriving at the gas pump only to find that your car won't start because the battery for the key fob was dead.

It is likely that your Subaru's key fob, regardless of whether it's old or new and can be replaced. Remember that some of the modern models, with their advanced technology, may require visiting a dealer. With a little time and effort, you can get your new key fob in place at home.

Begin by looking at the circuit board for the transmitter inside your key fob (instructions for opening the case should be included in the owner's manual). It should have one or two sets of serial numbers, each of which has 8 digits long. Write down the first number series and keep it handy to refer to later.

Then, get into the driver's seat, and close all the doors. Turn the key to start the vehicle and then switch off after ten revolutions. Press the lock button on the key fob and open the door to test that your doors are working properly. Then close the door, and take the key out of the ignition. You should hear the chime from your vehicle to indicate that the key fob is programmed.

Ignition System

The battery in your key may be dead If your Subaru keys aren't working as they should. You can replace the key fob battery on your own if you know how. A replacement battery is cheap and fairly easy to find. If the key fob doesn't respond to your commands it could be an issue with a different cause. To find a spare, it's best to go to an authorized dealer. They'll ensure that the key is genuine subaru replacement key fob key, under warranty, and Keyless that it will be programmed for your vehicle. This is a lot easier and Keyless safer than purchasing an aftermarket key from a website.

You can also request that the dealer cut a brand new key if you supply them with your VIN number and evidence of ownership. The information provided will be used to create a code for the replacement key so that it is recognized by your immobilizer. This is more complex than cutting a new key, and the dealership will usually charge more for this service.

Once the new key is programmed, you'll be able to switch it to your current key. It will only take you five seconds to insert the new key, so be sure to keep your working key at your side. You can take the key off after the security light has been off and you've tested it.

Battery Replacement

subaru key programmer fobs are very useful as they can switch on the sunroof and power windows of your vehicle with just one button press. However, the battery that is in your Subaru fob isn't designed to last forever and will eventually need to be replaced. It's good news that replacing the battery is a simple procedure that you can do yourself with the help of this short guide from Capitol Subaru.

To start you'll need to find the small crevice within the seam that divides the back and front of your key fob. You can cut this gap using a flathead screwdriver to reveal the small compartment that houses the battery. Remove the old battery, and then put in a new one, making sure that it is facing the right side up. Once everything is reassembled, you can use your new key fob to lock or unlock your vehicle with ease!

It's always an excellent idea to keep an additional set of keys on hand especially if you've lost them or they're not working properly. A new key can be purchased at your local dealership for cars or you can have one cut from an locksmith. In either case, it's vital to get your key fob working properly in the shortest time possible to allow you to drive safely!