• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Your first line of defense is your door lock. It will prevent unauthorized entry to your home. The signs of wear and tear as well as instances like moving into a new house or burglaries, may trigger the need to replace your lock.

cost to replace upvc door lock mechanism begin, determine the size of your cylinder using the distance between the adjustment screw and the center of the cylinder knob. This measurement will allow you to purchase the right-sized lock.

Deadbolt

Installing a deadbolt can be a excellent way to protect your door from burglars. The bolt extends into the strike plate that is on the doorframe when locked, making it more difficult for a burglar to break in through the door. A single-cylinder deadbolt is activated by a key located on the outside and the thumb-turn mechanism that is located inside. A deadbolt is only effective when it's properly installed however.

You will first need cost to replace upvc door lock mechanism find out if the door has an existing hole for a deadbolt or if you'll need to bore it out. Using the template that comes with the lock installation kit, mark the spot of the deadbolt's hole on the door's surface. Then, use your tape measure to determine how high the deadbolt needs to be. Mark this height on the door edge and use the speedsquare to draw a straight line across the mark that you made for the bolt hole.

Then, use a drill to drill this area until the hole extends to the opposite side of the door. This could take a while. Then, sand the hole and the edges of the door until it is smooth. It's also recommended to stain or paint the door at this point.

When the door is in place, remove any screws visible on the existing deadbolt. This will reveal the front and rear assemblies of the deadbolt and its internal bolt. Then, remove the bolt and replace it with a brand new bolt that matches the door hardware. The bolt is typically attached to a set plate that you need to unscrew. After this, you'll need to chisel the area on the door frame to accommodate the strike plate.

If your strike plate is not aligned, it's likely because the previous installer didn't properly mortise it or a weatherstripping popped up and changed the strike position. It is necessary to re-mortise the strike plate and possibly even the deadbolt to fix this issue. After this is done Test the deadbolt by closing and locking it. Be sure the bolt is extending into the strike plate then test the key to make sure it closes and opens effortlessly.

Knob

If a door knob is worn out, it can make your home or business less secure. It may also make it harder to open or close the door, making it recommended to replace the knob. It shouldn't take longer than 30 minutes. You can use a screwdriver as well as pliers to get rid of the knob or handle that was previously used Be careful not to harm any of the other components on the door.

Spray WD-40 or another dry lubricant on the mechanism of your door knob prior to you begin. This will allow the new lock to slide smoothly as you turn it. It is essential to choose the best knob and handle that matches the doors you currently have to ensure that the lock is operating properly. If you don't have a matching doorknob, you will need to purchase a replacement.

To begin the replacement process, look at the knob or handle to see what screws are holding it in place. If there aren't any screws, you can use the screwdriver to insert the cover plate into the screws plate that is hidden.

After removing the old knob take it apart and look for signs of rust and damage. If the knob has any dents or marks then you'll need to clean it. Otherwise it shouldn't need any major work.

Now it's time to install the new one. Before you do that, look over the new knobs to make sure that you're choosing the right one for your door. You'll need to pick one with an extending rod that locks with the rod mechanism of the second knob. After you've inserted the new knob into the hole and then put it in the latch.

Test the spring by pressing down on it repeatedly. The latch should then spring back up each time. Install the second knob and lock it to the rod mechanism of the first knob. Then, thread the other long screws from the knob's interior through the cylinder hole on the doorknob outside and secure it.

Latch

A latch is a steel piece that extends into the door jamb to keep it closed. It is operated by a knob or handle on the inside of the door, or a thumb turn on the outside side of the door. A deadbolt can be used to secure a latch and keep burglars from piercing the glass of the door. It also provides protection from the accidental or deliberate closing of the door by children or pets. You can install a latch with either a single-cylinder or double-cylinder deadbolt, depending on your preferred level of security.

Installing a deadbolt can be the same as installing a latch however there are some differences. First, measure the setback of the doorjamb with a tape measure to make sure that the new lock will fit. The setback is the distance from the edge of the doorjamb to the center of the hole to accommodate the latch faceplate. A typical setback is 2 3/8 to 2 3/4 inches. If you have a higher setback, you may have to purchase a more substantial latch from a hardware store or locksmith.

Then, make a hole for the latch plate at the edge of the doorjamb. Use a chisel and cut the mortise of the latch. Make sure that the depth is sufficient for the faceplate to be flush with the doorjamb. Place the strike plate in place to ensure that it's in the right position.

If the strike is too high, you could push the door back or apply pressure using a tire iron or crowbar. This can cause the doorjamb to crack. To correct this, the strike can be reduced by drilling a second hole in the doorjamb and chiseling out the core of the old hole.

The last step is to put in the new strike plate, which is done by screwing it over the screw holes that are already in place. Use wood putty then to fill in any existing holes for screws or bolts that won't be used. When the putty is dry, sand it smooth for professional results.

Strike

An electric strike is a metal piece that holds the deadbolt and latch are engaged when the door is closed. It is a vital component of the security of a lock, because it seals the upvc door locks replacement and provides extra resistance to force or kicking applied to the composite door replacement lock. If a door has been equipped with an electric strike, it will only be opened by a key or the control unit that governs the electrical impulses.

Traditionally the installation of an electric strike involved cutting a small portion of the doorjamb in order to release the latchbolt of a cylindrical lock from the pocket of the strike. This change can be a drawback in terms of the appearance of openings as well as exposing the mechanism of the latchbolt and keeper to unintentional users.

Recently, a number of electric strike manufacturers have developed a "No Cut" type of strike that does not require a cutout in order to operate. The strikes use a unique design to allow the latchbolt and keeper to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike is equipped with an internal ramp which lifts the latchbolt as well as the keeper when it receives a signal from the reader. The retracting of the keeper and latchbolt raises them on the ramp, Replacing upvc door lock mechanism locking the door. When the door is shut, the deadbolt remains in place and the latchbolt retracts in the keeper.

Installing an electronic strike is a simple procedure, especially when you're replacing upvc door replacement lock door lock mechanism - try this - an older strike. If you're planning to upgrade an existing access control system to an electric strike, you must make sure that the new system is compatible. It is also necessary to make sure that the strike is properly connected to your access control system and is set up to operate in a safe manner.

Upgrade your strike plates to high duty strike plates to prevent unauthorised entry. The plates utilize four to six three-inch screws instead of the two, three-fourth inch screws typically used in standard strikes. These screws are longer and make breaking the frame to reach the piece that turns the thumb on a single deadbolt for a cylinder more difficult.