• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a 2013 kia optima Key Sportage Replacement Key

The key in many Kia models comes with the keyless entry feature built in. This key typically resembles an remote control, and can be changed by a new one purchased from an Kia dealer or locksmith.

Key fobs can stop working due to a number of reasons, such as a dead battery, worn-out buttons, signal interference or water damage. Here are some suggestions on how to get your Kia Sportage replacement key for kia sportage key to work again.

How do you replace a smartkey or remote key?

The battery inside your kia sportage key's smart key will eventually have to be replaced, regardless of whether it is a remote key as well as a push-to start key or a standard metal key that is not equipped with transponder. This is particularly in the event that your vehicle displays a message that indicates that the remote or smart key is not powered by the battery.

Fortunately, it's quite simple to do. In order to replace the battery on the key fob remove the mechanical key from the hole in the back of the key fob. Then break the cover. A small screw will be found inside the key fob that holds the battery in the correct position. Utilizing a small screwdriver loosen the screw and pull out the battery that was in place. Then insert the new one and close the slit on the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock as expected, then you're all set! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or you have to complete errands in Brandon.

Note: Certain keys may require to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your key needs to be reprogrammed, you must be aware of the key code number printed on the tag of the key code and keep it in a safe place.

How do you replace a dead battery?

If your kia smart key key fob isn't responding when you press the lock or unlock button on the fob, this is a signal that the battery needs to be replaced. A battery that is not functioning properly can cause other issues, like the check engine light appearing or the engine not working properly. It is fairly easy to replace the key fob batteries by using only a few simple tools.

Make sure you turn off your vehicle and close all doors before you begin. Find the small, metal or plastic piece at the bottom of your key fob, and play with it until a metallic key pops out. You can then insert this key into the handle of the door for the driver to open your car.

To replace the key fob's battery, take off the cover on the rear and use a plier bar tool to loosen the latch holding the black negative battery cable. Take the old battery out, and then place the new battery in a way that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid damaging or breaking the contacts made of metal.

After you have installed the new battery and turning the key fob on and off in the ignition until the door locks up. Then, you can test your Kia key fob to check whether it's working again.

How to replace the smart key

You may have either a standard keyfob, or a Smart Key, based on the model of Kia Sportage. The difference between the two is that the smart fob has tiny mechanical key blade tucked inside it, while the standard fob isn't equipped with. Both kinds of key fobs contain an internal battery that will eventually need to be replaced. This is a straightforward process which takes just two minutes.

Before you start it is essential to ensure that you are on a flat surface with adequate lighting and that your Kia is not on. Also, keep in mind that there are tiny pieces inside the fob that could be removed if not cautious.

The release button for the small size is located on the lower backside. It will be a circular button or rectangular slot. Once you press this button, the mechanical blade will pop out and you can then open the key fob.

After the key fob has been removed, you can remove the battery that was in it. The new battery is one called CR-2032 and can be purchased through the internet or at a local auto parts shop. Once you're done with the battery, you should be able to lock, unlock and start your car using your key fob, even if your engine isn't running!

How do I replace the mechanical key

The Kia keyfob is a wonderful convenience that lets us lock or unlock our car by simply pressing one button. But like any device, it can have problems occasionally. There are ways to fix these problems and keep your key fobs working for an extended period of time.

A low or dead battery is one of the most frequent problems. This can cause the device to cease working or even to stop working intermittently. If this is the issue it is time to replace the battery an entirely new battery.

If this doesn't solve the issue, use an ordinary screwdriver with a flat head to push the plastic casing of the fob open. Be careful not to damage internal components or scratch the plastic. After the battery has been removed, replace it with a brand new one.

Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to verify that it's working properly. Contact a dealer or locksmith to solve the issue in the event that the key fob is not working. To avoid a lockout in the future ensure you purchase an emergency key that can work in all of the door and trunk cylinders.