• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Window Handle Replacement

It is easy to replace a broken window handle using the appropriate tools. It is important to know the type of handle you have and the spindle's size before you purchase a replacement.

Older uPVC window handles have a spur that extends and is locked over the wedge striker. They can be left or right-handed and must be to be matched when replacing.

What kind of lock or handle do you have? I have?

There are a myriad of window locks and handles made from upvc each with its own advantages and purposes. The type of handle you are using will determine the ease to open your windows and whether or not the locking mechanism works according to the plan. Over time and through regular use, window handles made of upvc may become damaged or worn out, making them less secure and effective. In some cases, they may even disappear completely. It is important to repair the handles on your window made of upvc immediately if you begin to notice them falling off. This will help to stop potential burglaries and ensure your home is secure.

Luckily, replacing your window handles made of upvc is a relatively simple task that can be done by nearly anyone. You will need a few tools, but with the right knowledge, it is simple and should only take a couple of minutes. You will need to be aware of the type of handle or lock that you have on your window. This will help you select the right glass replacement for windows.

Inline Espagnolette Handles

These are the most commonly used type of upvc handle and are typically located on the other side of your window. They are flat and feature an opening that engages the locking mechanism of the window frame. Inline upvc handles also have a spindle that runs through the centre of the handle and then into the frame of the window to activate the latch.

Cockspur Handles

They are typically found on older uPVC window frames and feature a distinctive, hook-shaped design. Cockspur handles are secured to the frame of the window with one screw, and are less secure than other kinds of window handle.

Handles that can tilt and turn

In contrast to other handles made of upvc, tilt and turn handles can both be rotated to open the window, and tilted inwards to allow ventilation. In general, they feature a 7mm spindle on the back of the handle. They are available in left and right handed versions.

When purchasing replacement window locks handles made of upvc It is crucial to verify the length of the spindle since not all of them are identical in size. Drop something in the middle of the hole to measure the length. This is the maximum size of spindle that will fit in your windows.

What is a spindle?

uPVC window handles operate similarly to doors. By turning the handle, you can open a latch in the frame. The window is then opened and closed. The handles can become damaged, particularly if they're often used or are exposed to harsh conditions. It is possible to replace the handles on your uPVC window if they are not operating properly.

There are several different types of uPVC handles to choose from, comprising Espag, Cockspur and Spaded handle options. They are designed to fit into the uPVC frames in various ways and each handle type has a particular spindle that is used to secure the mechanism to the window. This is why it is essential to know the kind of handle you have installed on your uPVC window to find the right replacement double glazing windows for it.

The base of the handle will tell you what kind of uPVC it is. There should be a'snap in' cover over one screw which holds the handle base in the correct position. Once you remove this, you will be able observe the second screw that holds the handle base in position. Once both screws have been removed and you are able to remove the handle from the uPVC.

After taking off the uPVC handle, carefully unscrew it from the locking mechanism. Note the length of the spindle. You'll need to buy a replacement windows panes of the same length as the handle that was originally used and the locking device.

The most common issue with window handles made of uPVC is that the spindle becomes worn out and can no longer operate the locking mechanism. This could be due to corrosion, damage from continuous use, or even an unreliable locking mechanism. When this happens it is required to replace the window handle as well as the locking mechanism to restore the full functionality to your uPVC windows.

How do I take off my old handle?

Through time and regular use, window handles may be damaged or destroyed, and if this happens, it is crucial to repair them as soon as possible to ensure the security of your home. It is good to know that replacing a damaged or worn handle is a simple task that can be carried out in less than one minute and doesn't require any special tools.

The first step in removing the old handle is to remove the screw that is situated on the top of the handle base. Once the screw has been removed, the handle can be pulled away. Another screw will be situated at the base of the handle. This too can be removed. Once the two screws are removed, the handle can be removed from the base of the window.

After removing the old handle, align the fixing holes of the new handle to the existing holes in the window frame. There might be a small cap or sticker on the new handle, so take them off the caps if needed, and then screw the handle in the frame. Once the handle is set, it is essential to check that it works by turning the handle, and ensuring that the lock mechanism is activated.

Espag handles come with an extra spindle that is protruding from the handle and slots into a multipoint locking mechanism inside the frame of the window. Cadenza windows come with a blade with cutouts that fit into the lock mechanism. Cockspur handles are long and are hung over the frame that surrounds the window or the transom crossmember of the bar.

After you have installed the new handle, insert the spindle inside the window lock and tighten it. Replace the snap-in cover and screw cap (if necessary) once the handle is securely fixed. The handle is now ready to use to use, so try opening and closing the window a few times to make sure that it works well and securely.

How do I fit the new handle?

It's not difficult to alter the handle on your windows made of uPVC. The process is very simple. You'll need an screwdriver and a bit of perseverance. First, make sure the old handle is unlocked. Then, remove any screws visible. You can also replace them using screw caps. After removing the handle, you'll need to take note of the length of the spindle that extends from the back. This is important because it will determine the kind of handle you will need to purchase.

Espagnolette handles are the most common type of handle for uPVC windows. The spindle passes through the handle to operate the locking mechanism within the window frame. The handle releases the latch and allows the window to open. When used regularly and over time, handles for espagnolette may be damaged.

Cadenza handles are a second type of uPVC window handle commonly used on tilt and turn windows. They feature an extended blade that works an interlocking mechanism that is multipoint within the window. They are usually more secure than espagnolette handles since they can only be opened from the inside. They can be replaced using the same procedure as espagnolette handles but you should ensure that the new handle has an angled blade as opposed to a flat one.

Once you have determined the right handle to purchase, you can simply align the new handle with the existing screw holes, and then screw it in the appropriate position. You should then put the screw covers back on and make sure your new handle is operating properly. This is accomplished by shifting the handle from the locked position to the unlocked and then back to the locked position a few times. It is possible to contact an expert to see how you can fix any issues. They can often advise you on the best way to solve the issue in a fast and effective way.