• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a 2011 Kia Soul Key Fob Sportage Replacement Key

The key in many Kia models comes with an electronic keyless entry system built into. This key is similar to an remote control and is exchangeable by an Kia dealer.

Key fobs can stop working for several reasons, including an empty coin battery worn buttons, signal interference, water damage and a damaged receiver module. Here are some helpful tips to help you get your Kia sportage replacement key working again.

How to replace a remote key or smartkey

It doesn't matter if your Kia is equipped with an intelligent key, remote key, push-to-start key, or regular metal non-transponder key The battery inside these keys will eventually need replacement. This is especially in the event that your car displays a message that the remote or smart key is not powered by the battery.

It's a fairly simple process. To replace the battery in the key fob, remove the mechanical key from the hole in the back of the key fob. Next, pry open the cover. A small screw will be located inside the key fob that holds the battery in place. Using a small screwdriver, take the screw off and remove the old battery. Then, insert the new and close the slit inside the key fob.

Once the key fob has a fresh battery check it by pressing the locks and unlock buttons. You're good to go in case the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers feel chilly or when you need to run errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming completed. This requires a programing machine, which is only available to the locksmith in the automotive or dealer. Other keys (non-transponder metal keys) don't require programming. If you're looking to reprogramme your key, you'll need to note the key code number on the key code tag.

How to replace the battery

If your Kia key fob is not responding when you press the lock or unlock button on the fob, it is a sign that the battery should be replaced. A low battery could cause other issues such as the check engine light flashing on or the engine not cranking. It is easy to replace key fob batteries by using only a few simple tools.

Make sure to shut off your vehicle and close all doors before you begin. Find the small, metal or plastic piece on the bottom of your key fob and play with it until a metallic key pops out. Then, you can insert this key into the handle of the door for the driver to open your car.

To replace the key fob battery, remove the cover from the back and use a pry bar tool to release the latch that holds the black negative battery cable. Remove the old battery, and then align the new battery in a way that the "+" positive side faces you, while the "-" negative side is facing the fob's metallic electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or breaking the metal contacts.

After you have installed the new battery and turning the key fob on and off in the ignition until the door locks cycle. You can then test your kia picanto spare key key fob to see whether it's working again.

How do you replace a smart key

You may have either the standard keyfob or Smart Key depending on the model of Kia Sportage. The smart key features an embedded mechanical key blade, however, the standard key fob does not. Both key fobs are equipped with an internal battery that will eventually require replacing. Fortunately, this is an easy process that will take about two minutes.

Make sure you turn off your Kia and sit on a level or well-lit surface prior to when you begin. Also, keep in mind that there are tiny components inside the fob that could be removed if not careful.

The first step is to find the small release button on the backside of the fob. It's either a circular or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened and you are able to remove the old battery, and replace it. The new battery is the CR-2032, and it can be purchased on the internet or at your local auto parts store. After you've finished, your key fob should permit you to lock and unlock your vehicle even if it's not running.

How to replace a mechanical key

The kia ceed key keyfob can be a fantastic convenience, allowing us to lock or unlock our car with just pressing a button. Like all devices like a key fob, the Kia can have issues at times. There are ways to address these issues and keep your key fobs in good working order for an extended period of time.

One of the most frequent problems is a weak or dead battery. This could cause your device to stop working or work intermittently. If this is the case try replacing the battery with a new one.

If this does not resolve the problem, use the flathead screwdriver that is standard to wedge the plastic casing of the fob open. Be careful not to scratch any internal components or scratch the plastic. After opening, carefully remove the old battery and replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia remote key fob fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to confirm it's functioning properly. Contact a dealer, or a locksmith to solve the issue in the event that the fob is not working. To avoid lockouts in the future, make sure you get an emergency key that will work in all of the trunk and door cylinders.