• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen are able to move large panes of tempered glass from a high point above the ground. They adhere to strict safety guidelines and frequently work in harsh weather conditions.

Wearing protective clothing, remove all glazing putty and metal glazing points using a utility knife. A heat gun may help soften the old putty and accelerate the removal process.

Replacement

When a window's pane is broken, it may be tempting to repair the glass instead of replace it. However, replacing a window is usually more cost-effective, and can also assist in preventing other issues in your home's energy efficiency. You should also consider the type of glass that is broken to determine if this is an interim fix or if you'll require an option that is more permanent.

The first step in fixing a broken window is to take off the frame, or sash, and lay it flat on a table. Wearing eye protection, gently wiggle the window's frame and pull out any remaining fragments. Utilize a utility knife to scrape off the glazing compound, and the glazing points that secure the window. Keep an eye on the components and where they are to ensure they are reinstalled.

After you have removed the frame and sash, you can begin to prepare to replace the glass. Before you begin, make sure that the opening in the frame is properly sized for your replacement window. Measure both ways across the opening, and then subtract 1/8 inch from each measurement to allow the expansion and contraction of the frame and glass. Then, buy double-strength glass cut to these precise dimensions. It is also an excellent idea to buy enough new glazier's points or clips to be installed every 6 inches around the window pane.

Based on the window's warranty the window may be covered by the manufacturer, in which case you should call them to file a claim. After the new glass has been installed, it should be covered with a thin layer of glazier's compound. After the compound has dried you can paint the frame to be a perfect match.

If you have a crack that is more than an inch, scoring the crack with a razor blade just beyond the crack will help stop it from spreading further. This trick won't be foolproof, but it can slow the development of the crack down to a manageable level until you can take more permanent measures.

Repair

Professional window installers are equipped with the appropriate tools and know how to handle different types of glass. They know how to dispose of waste in a safe manner, so they are less likely than other contractors to leave behind pieces of glass that could inflict harm on family pets or members of the family. They are also familiar with working with various types of windows, and may be able spot problems that an inexperienced home owner might not be able to notice.

Before beginning the process of repairing damaged window glass, be sure that you wear safety goggles and gloves. A small crack could cause shards of glass to fly away and put anyone at risk in or around the home. It is also crucial to determine what caused the crack in the first place, as it could help avoid future issues.

Make a two-part mixture of epoxy. They typically are a 50/50 mixture of resin and hardener and must be mixed quickly. When the mixture is done, apply it to the glass crack and allow it to dry. It should take only about a few minutes, but you must be quick because the mixture is extremely thick and drys quickly.

Once the epoxy is dried, you can get rid of any excess using a putty knife. You'll need to clean the cracks in the glass. If you don't clean it correctly, the resulting residue could cause further damage to the glass. Use a putty blade to smooth out the compound around the edge of the window and then match it to the frame made of wood.

To make a more durable option you can consider using a plastic covering. You can cover the glass using masking tape or a sturdy trashbag. This will stop the crack from expanding and will also keep out wind, water, bugs, and debris.

You can come up with an interim solution when you are unable get to the window in a timely manner. Simply apply a small amount of the stuff around the outside of the broken pane. It won't completely fill the gap between frame and glass however it will keep the break in place while you fix it.

Repainting

Repainting old glass windows is a good idea. This is a low-cost alternative to replacing your windows and can provide your home with a new appearance. Make sure the window is clean prior to painting. Clean the window using water and soap or ruby alcohol to eliminate oil smudges and other residues which can hinder the paint from adhering. Wear rubber gloves when working on glass to avoid the risk of transferring your own oils onto the surface of the window. In the end, you should apply several thin coats of paint instead of one thick layer. This will help the paint last longer and keep your windows looking smooth and even.

If you're planning to paint your glass windows, make sure you have the proper tools nearby. You'll require a brush or sponge, painter's tape, a ruler, toothpicks, and installed a few other tools, such as paper towels or a rag. You'll need the paints and brushes that you will be using on hand. Be sure to follow the manufacturer's directions and have plenty of patience since it may take a while for the paint to dry.

If you're using solvent-based paint, make sure that the area where you work is well ventilated. This will lower the risk of breathing into harmful chemicals and allow the paint to dry quicker. Use a protective mask when using spray paints.

For older glass windows, you'll need to prepare the surface before painting. Use soap and warm water to thoroughly clean the glass window. Then, use rubbing alcohol on any grease or oil remnants that may hinder the adhesion of the paint. Make sure the windows are dry prior to coating them.

If your glass windows are energy-efficient dual pane windows, you may be eligible to file a claim with the dealer or window company that sold them to cover any repair or replacement costs. This is especially true if you have experienced multiple problems with condensation or broken glass and the windows are covered under warranty.

Sealing

There are many ways to address the issue regardless of regardless of whether you have an old double-pane window that has cracks in the seal, or if you have an upgraded insulation unit (IGU) that has experienced defogging. It is the most expensive option to replace the IGU that is insulated as well as the frame. However, it may be required in situations where fog or condensation is causing energy loss. Other options include replacing the existing IGU with a single-pane or repair it by drilling a small hole through the bottom of the unit and then filling the solution with anti-fog.

You can also fill in the gap between the window frame and the sill or threshold by using a felt strip, vinyl v-strips, or a door sweep. Felt can be stapled, glued, or placed in place, but does not offer much protection against moisture. Vinyl weather stripping v-strip is durable and easy to put in, but it can be expensive and is generally reserved for areas exposed to high abrasion. Door sweeps are able to be easily nailed to the floor and are affordable. However, they provide only a small amount of protection between the threshold and air.

To repair a broken window seal make use of a putty blade to remove the old caulk. Wearing gloves and eye protection take care to remove the glazing points -- tiny fasteners that pin the glass into the frame's recess using sharp and pointed ends. After removing the glazing points, clean the grooves and sand the wood. Wipe off any sanding debris then seal the wood surface using a linseed oil-based paint or clear sealer.

A putty or caulking knife can be used to apply the traditional glazing putty, but using a knife will give a more precise application, and a more secure seal. Choose a putty that is made specifically for glass windows as it will be more adhesive and durability.

Apply a small amount the putty to the inside edge of the frame where it meets the glass. Slide the window repairs near me into the frame so that the cut line on the glass is aligned with the edge of the frame. Apply pressure to the glass to press the putty and create a tight seal. Smooth the compound with a gloved hand installed and remove any caulk or drips that were not properly applied before it has dried.