• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a great option for modern homes. They are durable, long-lasting and easy to maintain. Unlike timber and aluminium, they do not rust or rot.

Regularly cleaning and lubricating UPVC windows and doors is vital. This will reduce costly repairs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows could cause significant damage to your home and even be fatal. It is crucial to take the time to ensure that you're doing all you can to keep your windows in good repair.

Single-pane windows are relatively easy to replace, and they will usually fit into the old frames very easily. However when windows with double panes are secured by internal beading it will be more difficult to remove the panes that are in place and replace them with new ones. In this situation, you will need to find some plastic spacers that assist the new pane to fit perfectly into the frame of the window.

If you are going to attempt to remove the window panes by yourself, it is essential to wear the appropriate safety equipment, including thick gloves and uPVC repair protective eyewear. You should also lay down a drop cloth before you begin working on the window panes so that any shards fall onto the fabric and not onto the floor which could cause them to be trampled under.

It's a great idea to tape the gap once the glass is removed. This will stop drafts and water from entering your home until a professional is able to repair the window. This will also act as a barrier that will prevent any intruders from getting access into your home. If the gap is large, you may think about an alarm door that comes with an integrated window as it will provide the best of both worlds.

2. Sagging

Upvc is a long-lasting, energy-efficient and affordable alternative to timber sash window. However, over time they may be afflicted by a variety of issues, including sagging. A sagging uPVC windows can cause issues with light, draughts, and even security. It is crucial to act as soon as you notice your uPVC windows are falling down.

To repair a window that is sagging, you can try repositioning the hinges. To accomplish this, you'll need open the window so that you can get to the frame. Then, you can remove the hinges at the top and bottom using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Close your window to check the fit after you've repositioned your hinges. If you are happy with the fit of the window, tighten the screws to secure them in place.

If you cannot reposition the hinges, you may have to replace the seal. Over time rubber seals can lose their elasticity and become dry and cause them to lose tightness. It is essential to replace your seal as soon as you can to keep your uPVC window waterproof and draughtproof.

uPVC handles could also loosen. Often, this is caused by screws that have become loose over time. However, it could be due to the fact that the handle mechanism has worn out. It's relatively simple to fix a loose upvc repairs near me handle. First, you'll need close the window and then perform a test to ensure that it fits. The corners of the sash should align with the casing joint. If it doesn't, you can use a screwdriver to loosen the handle and turn the mechanism back into its original position.

3. Water Leaks

If you wake up to wet floors and damp walls every time it rains it is important that you take action. Water leaks through windows can cause structural damage to your home and also affect your ability to regulate the temperature in your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be completed by any competent DIYer. Based on the severity of the issue the caulking used previously might need to be removed before a new layer of caulk can be applied. When it comes to uPVC repair, you must be careful not to over-caulk. This will only make your window more difficult to clean and reduce its energy efficiency.

It is important to check that the drainage holes are free of debris and that the sill pan is angled in a way that allows it to drain away from the window. In more serious cases you might need to consider replacing the window.

Mold spots and rotted sills are other signs of water leakage. This mold thrives in damp environments and can quickly spread across the home.

It is also important to keep in mind that if the leakage is coming from between the glass in your double glazed windows, it is more likely to be a problem with the glass seal rather than the frame or sliding. This can be easily fixed by a uPVC window specialist who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault for the reason that your uPVC window is difficult to open or it blows open with the breeze. These are easily replaced by any competent DIYer and can usually be done within a few minutes.

Most households in the UK will have top-hung or side hung uPVC windows that have hinges and like any mechanical part they will wear out over time. Changing a window hinge is essentially a simple process but it can be easier to do with someone else to assist in holding the frame up.

Check that the uPVC hinges are closed and open in the right direction. This can be done by looking for the arrows on each hinge. This indicates the direction in which the window should open.

The issue could be caused by opening the window improperly or due to a poor installation at the factory. This issue can be fixed by sending us a photograph via our website and we will be pleased to offer you advice.

Regularly lubricating the hinges is essential. Applying a light engineering lubricant to the hinges is a great way to do this. We recommend using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can help the window operate and close more easily. It can also stop corrosion and decrease the chance of sticking. This must be done at a minimum once a year. WD40 or other solvent-based lubricants should not be used as they could damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by a variety of different things. The hinges, also because of wear and tear, may become displaced, which causes a gap to form between the sash and the frame. These can be easily repaired by giving them a good cleaning, but when they're beyond repair, it could be necessary to have them re-aligned or replaced. The second is the interlock, which is on the hinge side of the window, may also become misaligned, again it may be feasible to give them a thorough clean, however in certain cases, it may be necessary to have these replaced.

The next most common reason for draughts are the window seals. They are prone to wear or damaged over time and will allow air to escape through the gaps. This can be prevented by replacing them with high-quality weatherstripping. Another option is to replace the upvc window with low-emissivity glass, this will help in regulating indoor temperatures, and also lessen the risk of draughts.

Lastly, one of the most effective methods to reduce the draughts in your home is to use an draught excluder. These are typically fabric tubes which are filled with a sort of filler and can be put on the windowsill on top. They can keep your home warm by blocking out cold air.

The windows made of upvc can remain a great source of insulation and security to your home by performing regular maintenance and repairs. However, it is important to recognize that all windows have a life span and they may reach a point where it is more efficient to replace them than fix them. If you are having issues with your upvc windows, it is always recommended to seek assistance from a professional immediately.