• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

High-voltage fuses of the expulsion type have fiber or glass-reinforced plastic tubes and an open end, and can have the fuse element replaced. For example, fuse holders for North American class RK fuses have a pin that prevents installation of similar-appearing class H fuses, which have a much lower breaking capacity and a solid blade terminal that lacks the slot of the RK type. Fuse bodies may be made of ceramic, glass, plastic, fiberglass, molded mica laminates, or molded compressed fibre depending on application and voltage class. In terms of protection response time, fuses tend to isolate faults more quickly (depending on their operating time) than circuit breakers. The blown fuse must be replaced with a new device which is less convenient than simply resetting a breaker and therefore likely to discourage people from ignoring faults. Pole-mounted distribution transformers are nearly always protected by a fusible cutout, which can have the fuse element replaced using live-line maintenance tools. In medium-voltage distribution systems, a power fuse may be used to protect a transformer serving 1-3 houses. The secondary distribution wiring appears to be a duplex bundle in which the MGN serves as both neutral and mechanical supporting strand.

On the other hand, replacing a fuse without isolating the circuit first (most building wiring designs do not provide individual isolation switches for each fuse) can be dangerous in itself, particularly if the fault is a short circuit. Automotive fuses are used to protect the wiring and electrical equipment for vehicles. Semi-enclosed fuses are fuse wire carriers in which the fusible wire itself can be replaced. Fuses designed for soldering to a printed circuit board have radial or axial wire leads. Some manufacturers have tested their fuses for up to 63 kA short-circuit current. There are several different types of automotive fuses and their usage is dependent upon the specific application, voltage, and current demands of the electrical circuit. For drivers with street parking only, there is something called the On-Street Residential Charging Scheme (ORCS), which allows owners of plug-in cars to write to their council to ask for them to install local charging devices. Charging challenges: A third of households in England don't have off-street parking.

Ceramic fuses have the advantage of a higher breaking capacity, facilitating their use in circuits with higher current and voltage. Large power fuses use fusible elements made of silver, copper or tin to provide stable and predictable performance. This standard superseded both BS 1363:1947 and BS 2814:1957. Only 3 A and 13 A fuses are specified. The first British standard for domestic three-pin plugs was BS 317 Hand-Shield and Side Entry Pattern Three-Pin Wall Plugs and Sockets (Two Pin and Earth Type) published in 1928. This was superseded in 1930 by BS 372 Side-Entry Wall Plugs and Sockets for Domestic Purposes Part II which states that there are only minor alterations from BS 317. In 1934, BS 372 Part II was in turn superseded by the first edition of BS 546 Two-Pole and Earthing-Pin Plugs and Socket Outlets. This was shortly followed by patents from W. B. Sayers and G. Hookham; these early designs had rectangular plugs with contact plates on either side. There are certain characteristics common to British mains plugs and sockets intended for domestic use. Switched and unswitched fused connection units, without sockets, use BS 1362 fuses for connection of permanently wired appliances to a socket-outlet circuit.

Alternatively if you have the appliances, check the details printed on the label on the appliances or embossed into the casing. Why is 240 volts used for some appliances? Most automotive fuses rated at 32 volts are used on circuits rated 24 volts DC and below. Fuses for low voltage power circuits may have bolted blade or tag terminals which are secured by screws to a fuseholder. Surface mount fuses have solder pads instead of leads. Such fuses can only be used outdoors. This means that fuses can only be replaced by the preset (Type S) fuse rating. High-power fuse means that these fuses can interrupt several kiloamperes. Renewable fuses have replaceable fuse elements, allowing the fuse body and terminals to be reused if not damaged after a fuse operation. Cartridge (ferrule) fuses have a cylindrical body terminated with metal end caps. Some cartridge fuses are manufactured with end caps of different sizes to prevent accidental insertion of the wrong fuse rating in a holder, what are electric cables giving them a bottle shape. The hot gases are then explosively expelled out of the end(s) of the fuse. Indicating disc - a coloured disc (flush mounted in the end cap of the fuse) falls out when the element is blown.