• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen can maneuver large glass panes from a height higher than the ground. They work under extreme weather conditions and adhere to strict safety guidelines.

Wearing protective clothing, remove the metal glazing points and all glazing putty using an utility knife. A heat gun may help soften the old glue and make it easier to remove.

Replacement

If a window pane breaks, it could be tempting to try and repair the glass rather than replace it. It is more cost-effective to replace windows and it will also help to avoid other issues in your home's efficiency. Consider the type of broken glass to determine if it's a temporary fix or if a permanent solution is required.

The first step in repairing a broken window is to remove the frame, or sash and place it flat on a work table. While wearing eye protection, carefully move the frame and remove any shards that remain within the window. Utilize a utility blade to scrape off the glazing compound, as well as the glazing points that secure the window. Keep an eye on the components and where they are so they can be reinstalled.

After the frame and sash are removed and the frame is removed, you can begin preparation to install the new glass. Make sure you check the opening of the frame is the right size for your replacement window. Measure both ways across the opening, and then subtract 1/8 inch from each measurement in order to leave room for expansion and contraction of the frame and glass. After that, you can purchase double-strength glasses cut to these exact measurements. It is also a good idea to purchase enough new glazier's clips or glazier's points to be installed every 6 inches around the window pane.

Based on the window's warranty the window may be covered by the manufacturer and in this case, you need to contact them to file a claim. Once the new glass is installed, it needs to be sprayed with a thin coating of the compound used by glaziers. After the compound has dried and dry, you can paint it to match the rest of the frame.

If you have a crack that is more than an inch, scoring a small arc with a razor blade just beyond the crack will help prevent it from spreading any further. This technique isn't 100% foolproof but it will slow down the progression of the cracked until you can take more permanent measures.

Repair

Professional window installers know how to deal with a variety of glass, and they have the tools necessary to do the job correctly. They also know the best methods for disposing of waste, so they're less likely to leave scraps that are left behind, which could injure family members or pets. They're also familiar with different types of windows, and they may be aware of issues that aren't apparent to an inexperienced homeowner.

Wear safety glasses and gloves prior to starting the process of repairing damaged glass. Even a tiny crack can cause shards of glass to fly around and could pose a danger to anyone inside or around the house. It is important to determine what caused the crack, so that you will help prevent any future problems.

Start by making an epoxy mix that is two-part. These are usually 50/50 mixture of resin and hardener, and must be mixed quickly. Once the mixture is done apply it to the crack in the glass and leave it to dry. It should take only about a minute however it is important to do it quickly because the mixture is extremely thick and fast drying.

Once the epoxy is dried, you can take off any excess with a putty knife. You'll then need to clean the cracks in the glass. If you don't clean it correctly, the resulting residue could cause further damage to the glass. After the glass has been cleaned, use a putty knife to smooth the compound along the edge of the window and match it with the frame of wood.

You could consider using a plastic cover for a more durable option. You can cover the glass with masking tape or a sturdy trashbag. This will prevent the crack from spreading and will also keep water, wind and bugs out.

You can come up with a temporary fix in the event that you are unable to access the window in time. Apply a small amount of silicone sealant on the edge of the damaged glass. It won't completely fill the gap between the frame and glass however it will keep the break in place while you repair it.

Repainting

Repainting your old glass windows is a great idea. This is a low-cost alternative to replacing windows and it can give your home a fresh new look. Before painting, make sure the surface is clean. Use rubbing alcohol or soap and water to get rid of oil smudges and other residues that could prevent paint from adhering. Wear rubber gloves when working on glass surfaces to prevent the transfer of oils from your fingers onto the surface. In the end, you should apply several thin coats of paint instead of a single thick layer. This will make the paint last longer and will keep your windows looking smooth and even.

If you're planning on repainting your glass windows, ensure that you have the appropriate tools in your arsenal. You'll need a brush or sponge, painter's adhesive, a ruler, toothpicks, and other tools like paper towels or a rag. You should also have the brushes and paint you'll use to complete the project. Make sure you follow the manufacturer's directions and have a good amount of patience since it may take awhile for the paint to dry.

If you're using solvent-based paint, you should make sure that the area in which you work is adequately ventilated. This will lower the risk of breathing in harmful chemicals and allow the paint to dry more quickly. Use a mask that is protective when using spray paints.

For older glass windows, it is necessary to prepare the surface prior to painting. Clean the glass thoroughly with soap and warm water. Then, use rubbing alcohol to scrub away any grease or oil that could hinder paint's adhesion. Make sure that the windows are dry before you begin to paint them.

If you have energy-efficient double glazed window repairs-pane windows on your windows, it may be possible to submit an insurance claim for repair or replacement with the window company or dealer who sold the windows. This is especially true if your windows are still under warranty and you've had numerous issues with condensation or broken glass.

Sealing

There are many ways to fix the problem depending on whether you have an old double-pane window with a cracked seal, or if you own an upgraded insulated unit (IGU) that has experienced defogging. It is the most expensive option to replace both the IGU that is insulated as well as the frame. However, it could be required in situations where condensation or fog is causing energy loss. Other options include replacing the IGU with a single pane, or repairing the existing IGU by drilling a hole in the bottom and filling it with an anti-fogging product.

You can also fill in the gap between the window frame and the threshold or sill with a felt strip, vinyl v-strip, or a door sweep. Felt can be stapled, glued or put in place, but it is not a great protection against moisture. Vinyl v-strips are simple to install and durable, installer but can be expensive. It is usually reserved for areas exposed to abrasions that are high. Door sweeps are inexpensive and can be fixed into place however they provide very little or no protection between the sill or threshold and dust, air, and other debris.

To repair a cracked window seal first, you must use a putty knife to take off the old caulk. Wearing gloves and eye protection remove the glazing point -- tiny fasteners with sharp pointed tips that secure the glass into the frame's recess. After removing the glazing points, remove the grooves and sand down the wood. Wipe away any sanding sludge then seal the wooden surface with a linseed-oil-based paint or clear sealer.

A caulking knife or putty can be used to apply the traditional glazing putty, but using a knife will give a more precise application, and installer a stronger seal. Make sure you choose a putty made specifically for glass windows, since it will have higher adhesion and a longer life.

Apply a small amount the putty to the inner edge of the frame where it touches the glass. Slide the window into frame so that scribed line on glass aligns with the frame's edge. Apply pressure to the glass to press the putty and glass into an elongated seal. Smooth the compound using a gloved finger and clean up any caulk that is applied incorrectly or errant drips prior to drying.