• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane is a nuisance. This could be an opportunity to upgrade to energy-efficient windows or insulated ones to enjoy benefits like increased comfort, higher resale value and reduced utility costs.

It's a project you can tackle yourself at less than the cost of hiring an expert. You'll need only the proper tools and a few minutes of your time.

Glass

replace upvc window handle your old single-paned windows with tempered insulated glass to increase the efficiency of your energy, reduce noise, and preserve the historic integrity of your old home. The majority of homeowners with basic hand tools can repair windows with ease. You will also need a replacement window pane, glazier's suggestions, pliers, and latex glazing putty. If needed you may use a heating gun to warm the old putty. Before starting, wear gloves and safety goggles as working with broken glass could cause injuries.

Take out any broken glass pieces that remain. It is recommended to use pliers, but a flathead can be useful as well. After that, use a wood chisel or putty knife take the remainder of the old putty around the frame and sash. Be careful to not break the window sash. Be careful and slow. This can be done best on a ladder, not the ground. Also, you should have someone lower to keep it in place.

Make sure the window frame is ready to receive the new pane when you have removed the old glue. Take measurements of the width and height of the opening for the sash by subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to the nearest hardware store or home center, and find a piece glass cut to size. You can also cut the glass by yourself if you possess the appropriate tools.

After putting in the new pane After installing the new pane, apply a small amount of caulking around the edges to ensure it is weatherproof. Install a glazier's pointing on both sides of the frame. This will ensure the pane. The points shouldn't be too tight that they create friction between the sash and frame, but they also should not be too loose.

Before putting the putty on, make sure to knead it until it's soft and free of lumps. Roll it into pencil-sized strips. Apply the first strip to the corner of the frame. Work from corner to corner and ensure that it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular metal pieces that help secure the glass into the window frame without damaging the delicate surface. It's easy to learn how to use this hidden tool, and you'll save money on the cost of a professional installation.

After removing the old putty, glazier points as well as any remaining leftovers clean the frame thoroughly with an utility knife. Lightly sand the wood in the rabbet grooves to smooth out rough areas. If you decide to sand the wood, ensure you protect it with painter's tape to avoid accidental damage.

Take measurements of the empty frame and near note down precise measurements. Take these dimensions to a hardware store or a home center, and have the new pane cut smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new window in the frame and push it in place using your hand. Make use of the chisel's point, or the edge of the putty blade to tap the glaziers' points as illustrated in Figure 11. The glazier's point should be in line with the top edge of your pane and the raised shoulders should be just below the lip.

Apply a thin layer glazing compound on the rabbet grooves and the edges of new glass. This will seal and protect the edges. Allow it to dry and cure completely.

Install the new window sash once the glazing compound has dried. First, you need to coat the wood with an even layer of linseed. This will stop the new putty from soaking in the moisture and deteriorating and cracking with time. Apply the coat using a brush or the tip of your knife, then use the chisel or the back end of the knife to gently hammer the new sash and glazier's point into the rabbet grooves. Repeat this process every 10 inches around the frame's perimeter.

Putty

A baseball that is thrown, an errant rock or a falling branch can cause a window pane to crack or break. Fortunately, windows can be repaired by simply putting a brand new piece in place. The glass is held in place by a small metal clip called a glazier's point and putty, which is often called glazing compound. Before installing a replacement pane, first take out the old one and clean the area using an abrasive and a pull-type paint scraper or an abrasive wood chisel. Wear safety glasses and gloves when working. You'll need a heating gun when the window is fixed into the frame.

If you're planning to install your original sash, you must remove the mold that holds the old pane. Then you can sand the sash down to make sure it's flat and ready to be re-caulked. Once the sash is installed and sanded, apply a fresh caulk made of silicone around the glass to ensure that it will not leak or change color [Redirect-302] over time.

Remove the glazing points from the rabbets, or the grooves in the sash that the glass is. If they're difficult to cut out, try placing the hand tool, such as a heat gun over them to soften them first. When using a heat tool, make sure to not scratch the sash or its railings.

Create the bed for your new pane by removing the old glaze and putty. Roll a piece of glazing compound between your hands, shaping it to be about 1/2-inch thick. Then, press it into the rabbets in which the glass will sit. The glass must be positioned against the putty on both sides. If needed, lightly tap your glass into the rabbet using your thumb.

If the new pane is cracked, you can cover it with a solvent-based glass glue or silicone caulk before pressing it into the sash. If the crack isn't sealed, you will need to use putty to keep the water out. Once the putty is dry, wipe the oily film off the glass and [Redirect-Java] allow it to dry completely before you paint. If you paint before the putty is completely dry, it will not form a solid seal and could leak or discolor over time.

Paint

If you've suffered a break in a window pane, you might be concerned about the expense of a new one. The truth is, replacing a single piece of glass doesn't need to be costly even if you do it your own. Even double-paned windows can be replaced at a fraction of the cost it will cost for a professional.

First, if you're working on a large window, make sure it is securely fastened to the frame. This job can be done relatively easy and fast with the appropriate tools and techniques.

When you are ready to begin with the removal of the window pane. Pry out the glazing points made of metal that are attached to it. These are basically small metal triangles which function as "nails" that hold the window in within the frame of wood. They are buried beneath a bead or glazing putty that hardens to a solid wedge which holds the wood frame firmly in position and hides the points.

After taking off the old pane clean the frame and the wood. Scrape off any paint that has been used, and sand the rabbet grooves where the glazing points were. Sand them down to bare wooden surfaces so you can paint the frames with the same color. After sanding, apply a coat of flax oil on the wood's surface to extend the life of the frame.

Next, measure the width of the window opening. It is necessary to take horizontal and vertical measurements of the entire opening, as well as the thickness of the old pane. To determine the exact size of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass in times of seasonal change. You can bring these measurements to a hardware or home improvement shop and get the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.