• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Change a subaru legacy replacement key Spare Key

If you have Lost Subaru Keys, Championsleage.Review, your Subaru car key, you should call a locksmith. They can usually cut new keys for you at a lower cost than the dealer.

Subaru car keys are typically either intelligent "push-to-start" fob remote keys or simple metal keys. The Fob key has a chip in it and it will require reprogramming.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. These remotes make use of the keypad of your car to communicate with the computer in your vehicle.

Subaru models offer a little known feature called PIN Code Access. You can utilize a personalized number sequence to open and start your vehicle. If you own a newer Subaru Forester, Outback, Crosstrek, WRX, WRX STI or Impreza that has this feature, consult the owner's manual to learn how to use it.

If your keys stop working, there's a high possibility that the battery in the key fob is dead. You can test the battery life of your key fob by using a portable tester or a multimeter that you have in your garage.

The next step is to remove the transmitter circuit board from the key fob to examine it. It will have one or two sets of eight-digit numbers, so note down the first set so you will be able to remember it later. Once you've completed this, you can begin programming your key fob at home. The procedure varies based on the year and model of your vehicle. However, it's generally easy enough to do yourself.

Key Fobs

Subaru's newest models are all equipped with key fobs that not only unlock doors and activate your lights, lock your gas cap, and even start your car. This last trick is particularly helpful if you've been at the gas station only to find that your car won't start because the battery in the key fob has died.

It is likely that your Subaru's key fob, regardless of whether it's brand new or old it is able to be replaced. Remember that some of the more modern models, which have their advanced technology, might require a visit to the dealer. With a little time and effort, you can have your replacement key fob in place at home.

Begin by looking at the circuit board for the transmitter inside your key fob (instructions to open the case should be provided in the owner's manual). It should have one or two serial numbers, each of which is 8 digits long. Keep the first series of numbers in your wallet for later information.

Then, sit in your driver's seat, and close all the doors. Turn the key ten times to start your car, then turn off. Press the lock button on your key fob, then open the door to test that your doors are functioning properly. Close the door, and then remove the key. You should hear your vehicle sound again, signalling that the key fob has been programmed.

Ignition System

The key battery could be dead If your Subaru keys aren't working as they should. You can replace the battery for your key fob on your own if know how. A replacement battery is cheap and easy to locate. If your keypad doesn't respond to your commands, it might be another issue. To obtain a spare key, it's recommended to go to an authorized dealer. They will make sure that the key is an original Subaru key, that is in warranty, and is programmed to your vehicle. This is much safer and simpler than buying an aftermarket key from a company via the internet.

The dealer will also cut keys for you, provided you give them your VIN number as well as evidence of ownership. The information provided will be used to code the new key so that it is recognized by your immobilizer. This is more complex than cutting a new one, and the dealership will usually charge a higher price for this service.

Once the new key is programmed, you can switch it with your working key. It takes just five seconds to insert the new key, so be sure to keep your working key close to the ready. You can take the key off after the security light stopped flashing, and then test it.

Battery Replacement

Subaru fobs are extremely useful because they can turn on the power windows and sunroofs of your car with just one button press. However, the battery in the Subaru fob isn't designed to last forever and will eventually require to be replaced. This short guide from Capitol Subaru will help you to replace subaru key the battery yourself.

You'll have to find the small gap that divides the front from the back of your keyfob. You can cut this gap using an flat-head screwdriver to expose the small compartment that houses the battery. Take out the old battery and then insert a new one, making sure that it is facing the right side upwards. Once everything is assembled then you can use the new key fob to lock, unlock, and start your vehicle effortlessly!

You should always have a spare set keys, particularly if yours is broken or lost. You can purchase a new key at your local dealership or have it cut by a locksmith. It is essential that your key fob is working well as soon as possible so that you can safely drive.