• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window pane Window Panes

A damaged window pane can be an inconvenience. It could be a chance to upgrade your windows to energy efficient or insulated ones and enjoy benefits such as improved comfort, increased resale values and reduced utility bills.

You can do it yourself for a less than what it would cost to employ an expert. It requires the right tools and an hour or two of your time.

Glass

replace window handles your single-paned windows with tempered or insulation glass to improve the efficiency of your energy, reduce noise, and protect the historic integrity of your home's older. The procedure of replacing a window pane is relatively easy and can be completed by anyone with basic hand tools. You will also need an extra window replacement panes pane, glazier's suggestions, pliers, and latex glazing putty. If necessary, you can use a heating gun to warm the old putty. Wear safety goggles and gloves prior to beginning. Working with broken glass could cause serious injuries.

Take out any broken glass pieces that remain. This can be done with pliers, however, a flathead screwdriver can also be used in a pinch. Then, use a wooden chisel or putty knife to take the remainder of the old putty from around the frame and sash. Be careful to not scratch the window sash. Be careful and slow. It is a good idea to work on a stable ladder rather than the ground and to have someone standing below the sash to help keep it in place.

Make sure that the window frame is ready to accommodate the new pane once you have removed the old glue. Take measurements of the width and height of the opening for the sash, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to a hardware store or home center and find a piece glass cut to size. You can also cut the glass yourself, if you have the right tools.

After putting in the new glass Apply a small amount of caulking to the edge. This will make the glass weatherproof. Then, place a glazier's tip on the frame's opposite side to secure the pane in its place. The points shouldn't be so tight that they cause friction between the sash and the frame but they should not be too loose.

Before applying the putty on the surface, knead thoroughly until it becomes soft and free of lumps. Then make it into pencil-sized strips. The first strip should be glued to the frame's corner. Work from one corner to the next and ensure that it is even and smooth.

Glazier's Points

The glazier's facets are small triangular pieces that allow glass to be secured into the frame of a window without damaging or scratching the delicate surface. It's simple to learn how to use this secret tool, and you'll save money on the cost of an expert installation.

After the old putty as well as glazier's points are removed, thoroughly clean the frame using a utility knife to eliminate any remaining traces. Lightly sand the wood into the rabbet grooves, if necessary, to smooth rough areas. If you do sand your wood, ensure you protect it with painter's tack to avoid accidental damage.

Take measurements of the empty frame and write down accurate measurements. These measurements can be brought to a home center or hardware store, and the new pane will be cut to a smaller size. This will ensure a secure fit and will allow room for expansion and contraction.

Place the new pane into the frame and push it in with your hands. Then use the point of your chisel or the back end of the putty knife to make a tap on the glazier's points, as illustrated in Figure 11. When you're done taping, they should be flush with the top edge of the pane, and the shoulders that are raised of the points should be below the rabbet's rim groove.

Apply a thin layer of glazing compound to the rabbet grooves and the edges of the new glass. This will seal and protect the edges. Let it dry and cure completely.

After the glazing compound dries, you're ready to install the new window sash. First, saturate the wood with a heavy coat of Linseed oil. This will prevent the new putty from soaking up the moisture and deteriorating and cracking with time. Apply the coat using a brush or the tip of your knife, then employ the chisel or back end of the knife to gently press the new sash and glazier's tips into the grooves of the rabbet. Repeat this procedure every 10 inches along the perimeter of the frame.

Putty

A baseball thrown at you or a rock that is errant or falling branch could cause a window to crack or break. Most windows can be repaired easily by putting in a new piece. The glass is held in place using a small metal clip called a glazier's point, and putty, often called glazing compound. Before installing a replacement pane, first take out the old one and clean up the area using the help of a rag, a pull-type paint scraper or the wood chisel. Wear gloves and safety glasses while working. You'll need a heat gun if the window is glued into the frame.

If you plan to reinstall the original sash, gently remove any molding pieces that hold the old pane in place. Then, sand the sash to ensure it's smooth and ready for new caulk. Once the sash is re-installed, apply a new caulk made of silicone around the glass to ensure it won't leak or discolor over time.

Take out the glazing points in the rabbets. These are the grooves on the sash where the glass is. If they're hard to chisel out, you can try holding the hand tool, such as a heat gun over them to soften them up first. When using a heating tool, make sure to not damage the sash's railings and sash.

Create the bed for your new pane after you have removed the old glaze points and putty. Roll a rope made of glazing compound between your fingers and then make it about 1/2 inch thick. Then, press it into the rabbets, where the glass will rest. It is essential that the glass is positioned against the putty on both sides So if you have to tap it, gently press the glass into the rabbet with your thumb.

If the new pane is cracked, you can apply the silicone caulk or glass glue based on solvents to fill in the crack before pressing it into the sash. If the crack is not sealed, you'll need to use putty to keep water from getting in. When the putty dries and the film is oily, wipe it off the glass using a rag and allow it to completely dry before painting. Paint before the putty is completely dry. It will not create a solid seal and could leak or discolor with time.

Paint

If you've had a broken window pane, you may be worried about the expense of replacing it. In reality, replacing a single pane of glass doesn't need to be costly when you do it on your own. Even double-paned windows can be replaced at a fraction of the cost it would cost an expert.

First, if you are working on a large-sized window, make sure it is securely fastened to the frame. This job is relatively easy and quick with the appropriate tools and techniques.

When you're ready to start, begin by removing the old window pane by removing the glazing points of metal that are attached to it. These are basically small metal triangles which function as "nails" that hold the window in within the frame of wood. They are buried beneath a layer of glazing putty that transforms into a solid molded wedge which holds the window in place and hides the edges.

After removing the old pane, clean the frame and wood. Scrape away any old paint and sand down the rabbet grooves, where the glazing points were. These should be sanded to the point of being bare, so that you can paint them the same color as the rest the frame. After sanding, apply a coat of flax oil on the wood that is not sanded down to help extend its lifespan.

The next step is to measure the dimensions of the window opening. You'll need to take horizontal and vertical measurements of the entire opening as well as the thickness of the old pane. To get the exact size of the new pane, subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. Take these dimensions to a hardware or home improvement store, and they will have a piece cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and replace window pane the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.