• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. Unlike timber and aluminium, they are not susceptible to rust or rot.

It is crucial to wash and oil UPVC doors and windows on a regular basis. This will prevent unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows could cause severe damage to your home and even be fatal. It is essential to make sure that your windows are in good condition.

Single-pane windows are fairly simple to replace, and they will usually fit into the frames that were previously in use very easily. If windows with double panes are held together by internal beading, it will be harder to remove and replace the old panes. In this instance, it is necessary to buy plastic spacers to make sure that the new pane fits into the window frame.

Wearing eye protection and heavy gloves is a must when you are planning to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes to ensure that any shards fall onto the fabric and not onto the floor and could be trampled under.

It's a good idea to tape the gap once the glass is removed. This will stop drafts and water from entering your home until a professional arrives to repair the window. This will also provide an obstruction to prevent intruders from getting into your home. If the gap is particularly large, you might think about a security door that has an integrated window, as it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber windows with sash. However, with time, they can suffer from a variety of problems including sliding. A sagging uPVC windows can cause problems with light, window Doctor draughts and even security. It is crucial to act as soon as you realize that your uPVC windows are sagging.

To fix a window that is sagging you can try repositioning the hinges. To accomplish this, you'll need open the window so that you can access the frame. After that, using an screwdriver, take off the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. After you've repositioned the hinges, close your window and verify the fit. If you are happy with the fit of the window, tighten the screws to hold them in place.

If you are unable to move the hinges, you may need to replace the seal. Rubber seals can dry out and lose their elasticity over time, causing them to loose their elasticity. If this happens, it's important to replace the seal as soon as you can to ensure that your uPVC windows remain watertight and safe from drafts.

uPVC handles can also loosen up. Most often this is due to screws that have become loose over time. However, it could be due to the fact that the handle mechanism has been worn out. It's fairly simple to repair a loose upvc repairs handle. First, you'll need to close the window and then perform an initial test fit. The joint at the corner of the sash must align with the joint on the casing. If it does not, you can use the screwdriver to loosen up the handle. Then, you can turn the mechanism back into place.

3. Water Leaks

If you awake to wet floors and mouldy walls every time it rains it is important that you take action. Windows that leak water do not only lead to the destruction of your home's structure but also hinder your efforts to regulate the temperature inside your home. The most common cause for leaking uPVC windows is that the sealant around the frame is either damaged or missing.

This is a simple fix that can be accomplished by any DIYer who is competent. Depending on how severe the problem is, the old caulking may need to be removed. It is important to remember that when it comes to uPVC window repairs, you should not be tempted to apply too much caulk in order to make the area harder to clean and could reduce your energy efficiency.

Make sure that the drainage holes have no debris in them and ensure that the sill pan has been properly angled to drain away from the window doctor (find more information). In more serious instances, you may need to replace the window.

Other indicators of water leakage include sills that are rotten and the appearance of black spots of mold on the wall near the window. This fungus thrives in conditions of dampness and can spread quickly throughout the house.

If the leakage is occurring between the double glazing-glazed glass, it is more likely the problem is with the seal rather than the frame. A uPVC specialist can easily solve this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and open in a breeze It could be the hinges that are at the fault. Any competent DIYer can replace hinges in just a few minutes.

Most households in the UK will have top-hung or side hung uPVC windows that are hinged and like any mechanical part they are susceptible to wear and tear over time. It's easy to change a window hinge, but it's easier if someone else helps hold the frame.

Verify that the uPVC hinges are closed and open in the proper direction. Look for the arrows that are on each hinge to determine which direction the window should be opened.

The issue can be caused either by opening the window incorrectly or a faulty installation in the factory. Sending us a photo via our website will often solve the issue. We are happy to give advice.

Regular lubrication of the hinges is essential. This can be accomplished by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can allow the window operate and close more smoothly. It can also reduce the risk of a window sticking and help prevent corrosion. This must be done at a minimum every year. WD40 and other solvent based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a variety of various factors. The hinges, also because of wear and tear, could become misaligned. This will cause gaps to develop where the sash meets the frame. This can be easily repaired by giving them a good cleaning, but when they're beyond repair, it could be necessary to get them re-aligned or replaced. Second, the interlock can be disaligned. This happens on the hinge's side, and may need to be cleaned. In certain instances it might be necessary to replace these.

These seals can wear down or be damaged over time, allowing air to escape. Installing high-quality weatherstripping can help stop draughts. Another option is to replace the upvc window with low-emissivity glass, this will help in regulating indoor temperatures and will reduce draughts.

Another, and most effective methods to reduce draughts is by using a draught excluder. These are typically fabric tubes that are filled with some sort of filler and can be positioned on top of your windowsill. These will help to stop cold air from entering and keep your home warm and cozy!

Your upvc windows can continue to provide excellent insulation and security for your home with regular maintenance and repairs. It is crucial to keep in mind that all windows will eventually become worn out, and it could be cheaper to replace them than to repair them. So, if you are experiencing issues with your Upvc windows, it is always recommended to seek help from a professional as soon as you can.