• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window screen replacement pane can be a nuisance. It can also be an opportunity to upgrade your glass to energy-efficient or insulated windows and enjoy benefits such as more comfort, higher resale value and reduced utility costs.

You can do it yourself for a fraction of what it would cost to hire an expert. It requires the right tools and an hour or two of your time.

Glass

Replace Window pane your old single-paned windows with tempered insulation glass to improve energy efficiency, cut down on noise, and preserve the original character of your home's older. The procedure of replacing windows is simple and can be done by anyone with basic hand tools. You will also require a replacement window handles replacement pane, glazier's suggestions, pliers, and latex glaze putty. If necessary, you can make use of a heat gun to warm the old putty. Wear safety glasses and gloves prior to starting. Working with broken glass could result in serious injuries.

Take away any broken glass pieces that remain. It is recommended to use pliers, but a flathead can be useful equally. Use a wood chisel, or putty knives, to take away any old putty that remains around the frame and window sash. Be careful to not damage the window sash. Take your time and work slowly. It is a good idea to do this on a stable ladder rather than on the ground and to place someone on the sash to help keep it steady.

Make sure that the window frame is ready to accommodate the new pane after you have removed the old putty. Measure the width and height of the opening in the sash, subtracting 1/8 inch from each measurement (to allow for replace Window pane seasonal expansion and contraction). These measurements can be taken to an hardware or home centers store to have cut a piece of stock glass to the right size. Alternatively, you can cut the glass yourself if have the tools you need.

After installing the new pane, run a small bead of caulking along the edge to make it weatherproof. Then install a glazier's point on the frame's opposite side to secure the pane into its place. The points shouldn't be so tight that they cause friction between the frame and sash however they should not be loose.

Before putting the putty on, make sure to knead it until it's soft and free of lumps. Make it into pencil-sized strips. The first strip should be placed in the corner of the frame, moving from one corner to the next so that it is smooth and even.

Glazier's Points

The glazier's points are small triangular pieces of metal which help to secure glass into frames for windows without scratching or damaging the fragile surface. It's easy to learn how to use this secret tool, and you'll save money on the expense of a professional installation.

After removing the old putty, glazier points, and any other leftovers clean the frame thoroughly using an utility knife. Lightly sand the wood into the rabbet grooves to smooth out rough areas. If you sand wood cover it with painter's tape to avoid accidental damage.

Note down the exact dimensions of the frame. Take these dimensions to an hardware store or home center and have the new pane made slightly smaller than the frame's opening. This will ensure a secure fit, and allow for expansion and contraction.

Place the new pane in the frame and press it into the frame with your hand. Make use of the point of the chisel or the back of the putty knife to tap in the glazier's points, as shown in Figure 11. After you're done, the points should be flush with the top edge of the pane and the shoulders of the points should be below the rabbet's lip. groove.

Apply a small amount of glazing compound over the edges of the new glass and in the rabbet grooves to seal and protect them. Allow this to dry and cure completely.

Once the glazing compound has dried and the glazing compound is dry, you can install the new window sash. First, saturate the wood with a thick coat of linseed oil. This will prevent the new putty drying out or cracking due to the moisture it absorbs. Apply the coat using a brush or the edge of your putty knife, and then use the chisel, or the back end of the knife to gently press the new sash and glazier's points into the rabbet grooves. Repeat this procedure every 10 inches around the perimeter of the frame.

Putty

A baseball thrown or a rock thrown by error or a branch falling could result in a broken or cracked window. The majority of windows can be replaced by installing a new piece. The glass is held into place by a small metal clip, called the glazier's point, and putty. This compound is also referred to as glazing compound. Remove the old pane and clean the area using a rag, a pull-type scraper or wood chisel. Wear gloves and safety glasses when working. You'll need a heating gun if the window is glued to the frame.

If you are planning to replace your original sash, you must remove the molding that holds the old pane. Then sand the sash to ensure it's level and ready to be re-caulked. After the sash has been re-installed then, apply a new caulk made of silicone around the glass to ensure that it will not leak or change color as time passes.

Remove the glazing points from the rabbets and the grooves in the sash where the glass sits. If they're difficult to cut, place an instrument such as a heatgun over them to soften first. When using a heated tool, be sure to not damage the sash or its railings.

Create a bed for your new pane by removing the old glaze points and putty. Roll a rope with glazing compound between your fingers, and then make it about 1/2 inch thick. Press it into the rabbets where the glass will be put. It's important that the glass is positioned against the putty in all places on both sides If you have to do so, gently tap the glass into the rabbet using your thumb.

If the new pane is damaged, you can use the silicone caulk or glass glue based on solvents to fill in the crack before pressing it in the sash. If not, you'll have to apply putty over the crack to create an impervious seal to keep water out. After the putty has dried and the film is oily, wipe it off the glass using a rag and allow it to dry completely prior to painting. If you paint before the putty is completely dry, it won't form an effective seal and could leak or discolor over time.

Paint

If you've had a broken window pane, you may be worried about the cost of a new one. The truth is, replacing a single pane glass doesn't have to be costly even if you do it your own. Even a double-paned window could be replaced for a fraction of what it costs for a professional.

If you are working on a large-sized window, make sure that it is securely fastened to the frame. Using the proper tools and techniques you can make this task relatively easy and speedy.

When you're ready to start taking off the old window pane by prying out the glazing points of metal that are attached to it. These are basically small metal triangles that function as "nails" that hold the window in within the frame of wood. They are buried under a bead of glazing putty, which hardens into a solid, molded wedge which holds the window in place and hides the points.

After removing the old pane, clean the frame and the wood. Scrape off any paint that has been used and sand the rabbet grooves that the glazing points were placed. They should be sanded to bare wood, to allow you to paint them the same shade as the rest of the frame. After the sanding process, apply a coat of flax oil to the wood that is not sanded down to help extend its lifespan.

The next step is to measure the dimensions of the window opening. You will need to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. To get the exact size of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass during seasons of changes. You can take these measurements to a hardware store or home improvement shop and get the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.