• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

In theatre and performance venues, rs485 cable RS-485 networks are used to control lighting and other systems using the DMX512 protocol. This high performance and high connectivity equipment also offered personnel easy configuration and operation to get the project underway as quickly as possible. The only possible reference is the reading of the displayed value, for example, of the current. The RS485 system used for Modbus communication provides a main cable (Bus or backbone), to which all the devices have to be connected with branches (also known as stubs) that are as short as possible. Because of the differential signal, any noise is subjected externally to the cable is basically subjected to both cables. Also, its robustness. It is a differential signal. Grounds between buildings may vary by a small voltage, but with very low impedance and hence the possibility of catastrophic currents - enough to melt signal cables, PCB traces, and transceiver devices. Line A voltage, implying A, the green wire, is indeed connected to the driver inverting signal, as seen in a whitepaper.

There are different families of products on the market: instruments which measure a single electrical parameter (voltage, current, frequency, and phase angle cosϕ), generally used in single-phase systems, as instrumentation on the machine, and instruments allowing all the electrical parameters to be measured and displayed, both for the single-phase system and for the three-phase system. The sizing of the measurement system begins with knowing the main parameters of the plant; in particular, from the characteristics of the protection switch, the type of distribution system, the rated current, the rated voltage and the type of busbar can be known. In order to ensure that the instrument is properly protected, fuses must always be fitted to the power cables of the digital instruments and to the measurement inputs of the voltmeter. Power to heat buildings is via 215 substations, of which 191 are connected to the Central Heating Plant, and 24 to the boiler room Podczele. Star and ring topologies are not recommended because of signal reflections or excessively low or high termination impedance.

This allows RS-485 to implement linear bus topologies using only two wires. 12 V. What RS-485 does, it just needs 5 V because it just swings over to 5 V at the output. In addition to the ease of integration, minimum requirement of processing power and reliability of the connectors further helps to favor these serial over Ethernet communications.A device server is used to control the whole setup via a networking technology. 1. RS232 - Can accept local power or can be cabled to run powered from port. Two auxiliary power cables should always be connected for digital instruments. The shielding may be braided (be formed by a mesh of thin conducting wires) or be a foil (consisting of a sheet of metal wound around the conductors): the two types are equivalent. Multiple receivers may be connected to such a network in a linear, multidrop bus. This connection may be used to limit the common-mode signal that can be impressed on the receiver inputs. It can drive things 1200 meters, which RS - 232 is about 15 meters maximum.

RS-485 can send data 1200 meters on cable. The branches must be no longer than 1200 m! After having defined the type of instrument best suited to the needs, if the measurement is performed by indirect insertion, the accessories of the measuring system, such as current and voltage transformers must be chosen with care. A current transformer suitable for the application must therefore be selected. RS-422 and RS-485 Standards Overview and System Configurations, Application Report (pdf). The EIA has officially disbanded and the standard is now maintained by the TIA as TIA-485, but engineers and applications guides continue to use the RS-485 designation. Thanks to paperless chart recording technology; students and teachers are now able to clearly and conveniently visualize their experimental data. Users now have the ability to monitor their live data and store all the information on the Brainchild itself or on a connected PC. Users can browse through the alarm list or acknowledge alarms easily via function keys on the vertical bar. Additionally, the Brainchild's standard Ethernet and optional RS-232/RS-422/RS485 communication enable users to access data onsite from a remote location via the RS serial interface or Ethernet networking. In connection with the need for rapid response by the central location for all types of heating systems failures and malfunctions substations located in many parts of the city, MEC Kolobrzeg decided to execute a remote system monitoring and control of heating systems.The monitoring system is based on Citect SCADA visualization software v. 6.0. This software is a standard for the entire heating system to monitor the MEC Kolobrzeg.Delivered new server running under operating system Windows Server 2003. Visualization of the nodes attached to an existing application that supports the entire heating plant.