• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen are able to maneuver large panes of tempered glass from a high point above the ground. They adhere to strict safety guidelines and are often working in extreme weather conditions.

While wearing protective clothing remove all glazing putty and glazing points using a utility knife. A heat gun can to soften and take off the old putty.

Replacement

When a window's pane breaks, it could be tempting to try and repair the glass rather than replace it. It is more cost-effective to replace windows and it can also help prevent other problems in your home's efficiency. Take a look at the type of broken glass to determine whether it's a temporary fix, or if a more permanent solution is required.

The first step in repairing broken windows is to remove the frame, or sash and place it flat on a table. Wearing eye protection, gently move the window's frame and then remove any remaining shards. Use a utility blade to scrape off the glazing compound and the glazing points that keep the window in place. Be sure to keep an eye on these components and their locations to ensure that they can be replaced later.

After removing the frame and sash you can begin preparing to replace the glass. Before you begin ensure that the opening in the frame is properly sized for your replacement window repairs. To allow for expansion and contraction of the glass and frame and contraction to both directions, measure the opening and subtract 1/8 inch. After that, you can purchase double-strength glasses cut to these exact dimensions. It is recommended to also purchase enough glazier's clips, or points to be installed every 6 inches around the window pane.

Depending on the window's warranty the window may be covered by the manufacturer and in this case, you need to contact them to make an claim. After the new glass has been put in place, it is important to cover it with a thin layer of glaziers compound. After letting the compound dry and dry, you can paint it to match the rest of the frame.

If you have a crack that is more than an inch, cutting an arc of a razor blade just beyond the crack can help to prevent it from spreading any further. This technique isn't 100% foolproof, but it can slow the growth of the crack down to a manageable level until you can take more permanent measures.

Repair

Professional window contractors are trained to handle a variety of glass, and they have the tools needed to complete a proper job. They are able to dispose of waste properly, so they are less likely than others to leave behind a mess which could cause harm to family pets or members of the family. They're also accustomed to working with various types of windows and could be able spot problems that an inexperienced home owner might not see.

Wear safety goggles and gloves prior to beginning the process of repairing damaged glass. A small crack could cause shards of glass to fly around and could pose a danger to anyone inside or around the house. It's also crucial to figure out what caused the crack in the first place, since it can help prevent future problems.

Start by making an epoxy mix that is two-part. It is usually a 50/50 mix of hardener and resin and they need to be mixed quickly. After the mix has been made, apply it directly to the crack and let it dry. It should only take some minutes, but it is important to work quickly because the mixture is very thick and drys very quickly.

Once the epoxy has dried, you can remove excess epoxy using a putty blade. Then, you'll have to clean the area around the broken glass. If you don't clean the area correctly, the residue could cause further damage to the glass. After the glass has been cleaned using a putty knife, you can use it to smooth the compound along the edges of the window and to match it to the frame of wood.

You could consider using a plastic cover for a more robust option. A trash bag that is heavy-duty or tarp is ideal, however you can also use masking tape to cover the glass. This will keep the crack from growing and will also keep out wind, water insects, water, and other debris.

If you're unable to reach the window in a timely manner, you can use silicone sealant to create temporary repairs. Simply apply a small amount of the material around the outside of the damaged pane. It won't fully seal the gap between the frame and glass, but it will keep the break in place while you fix it.

Repainting

If your glass windows are old, you may want to repaint them. This is a low-cost alternative to window replacement and will give your home a new appearance. Before painting, ensure that the surface is clean. Use soap or rubbing alcohol and water to remove oil smudges, and other residues which can prevent paint from adhering. Wear rubber gloves when working on glass surfaces to prevent the transfer of oils from your fingers onto the glass. Finally, you should apply several thin coats of paint instead of a single thick layer. This will allow the paint to last longer and ensure that your windows appear even and smooth.

If you're planning to paint your glass windows, ensure that you have the appropriate tools in your arsenal. You will need either a brush or sponge as well as a painter's tamper as well as a ruler and toothpicks. You should have the brushes and paints you'll be using on hand. Be sure to follow the manufacturer's directions and have plenty of patience as it can take some time for the paint to dry.

If you're using solvent-based paint, you should also ensure that the room where you work is well-ventilated. This will reduce the chance of inhaling toxic chemicals, and the paint will dry more quickly. You should also make sure you wear a mask that is protective for any spray paints that you use.

You'll need to clean the glass window thoroughly using warm water and soap before you paint it. Make use of soap and warm water to thoroughly clean the glass window. Then, use rubbing alcohol on any grease or oil residues that might hinder the adhesion of the paint. Be sure that the windows are dry before you begin painting them.

If your glass windows are energy-efficient dual pane windows, you might be able to file a claim with the window manufacturer or dealer that sold them to pay any repair or replacement costs. This is especially true if your windows are still under warranty and you've had numerous issues with condensation or broken glass.

Sealing

Whether you have old double-pane windows with damaged seal or more recent insulated glass units (IGUs) that have experienced fogging or fog, there are many options to address the issue. The most expensive option is to replace the frame and insulated unit, but it may be necessary if condensation or fog are causing energy loss. Other options include replacing the IGU with a single-pane, or repairing it by drilling a small hole in the bottom of the unit and filling the solution with anti-fog.

You can also close the gap between the window frame and the threshold or sill with a felt strip, vinyl v-strips, or door sweep. Felt is cheap and can be fixed by gluing, nailing, or stapled into place however it doesn't provide much protection from moisture. Vinyl v-strips are easy to put up and is durable however it can be expensive. It is generally reserved for areas that are subject to high abrasion. Door sweeps are cheap and can be fixed to the floor, but they create virtually no barrier between the sill or threshold and dust, air and debris.

To fix a damaged window seal make use of a putty blade to scrape off the caulk. Wearing eye protection and gloves take out the glazing point -- tiny fasteners with sharp, pointed tips that pin the glass in the frame's recess. Once you have removed the glazing points, scrub the grooves and sand the wood smooth. Clean any sanding residue and then seal the unfinished wood with a linseed oil based paint or clear wood sealer.

A putty or caulking knife can be used to apply traditional glazing putty, but a knife will provide a more precise application, and a more secure seal. Choose a putty that is made specifically for glass windows, as it has better adhesion and durability.

Apply a thin layer of putty across the inside of the frame where it meets with the glass. Slide the window into the frame so that the drawn line on the glass lines up with the edge of the frame. Apply pressure to the glass in order to force the putty into a solid seal. Smooth the compound with an ungloved finger, and wipe away any mistakenly applied caulk or errant drips before it is dry.