• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are easy to maintain and are durable and long-lasting. They are not susceptible to rot or rust like timber and aluminum.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will reduce repair costs and improve energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a great amount of damage to your home, which can make it very dangerous and potentially fatal. It is essential to take the time to make sure that you're doing everything you can to keep your windows in good repair.

Single-pane windows are relatively easy to replace, and they typically fit into old frames very easily. If you have double-paned windows which are held together by internal beading, it is difficult to remove and replace the panes that were previously in use. In this instance, it is necessary to purchase plastic spacers to make sure that the new pane fits into the window frame.

If you're planning attempt to remove the window panes by yourself, it is essential to wear the appropriate safety equipment, including thick gloves and protective eyewear. It is also recommended to lay down a drop cloth prior to when you begin working on the glass so that any shards fall onto the fabric instead of landing on the floor where they can be trampled on and cause further damage.

After the glass has been removed from the window, it's best to cover the gap with packaging tape or duct tape to block water and drafts from getting into the property until a professional can come out and repair the window. It also acts as a barrier, deterring any intruders from gaining entry into your home. If the gap is particularly large, you might be interested in a security door that has an integrated window, since this will offer the best of both worlds.

2. Sagging

uPVC is a durable, energy-efficient and affordable alternative to timber sash window. However, with time, they are susceptible to a range of issues, including sliding. A window that is sagging can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to sag it's crucial to act fast to prevent the problem from getting worse.

To fix a window that is sagging you can try to reposition the hinges. To do this, you'll need open the window so that you can access the frame. Then, using an screwdriver, take off the hinges at the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to check the fit after you've moved your hinges. If you're happy with the fit, tighten the screws to ensure they remain in place.

If you aren't able to move the hinges, you may require replacing the seal. As time passes, rubber seals lose their elasticity and dry out, which causes them to loosen. If this happens, it's important to replace the seal as fast as you can to ensure that your uPVC windows are watertight and safe from drafts.

uPVC handles could also loosen. This is often caused by screws that have loosened over time, but it could be caused by the handle mechanism wears out. It's a good thing that it's simple to repair the handle of a window that is loose yourself. First, you'll need close the window and then perform a test to ensure that it fits. The joint at the corners of the sash must align with the joint on the casing. If it isn't, you can use a screwdriver to loosen the handle and then return the mechanism to its original its original position.

3. Water Leaks

It is essential to take action if you awake each day to find mouldy walls and wet floors. Water leaks from windows are not just a cause for destruction of your home's structure but also hinder your efforts to control the temperature in your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or is missing.

This is a relatively easy fix that can be done by any skilled DIYer. Depending on how serious the issue is, old caulking may need to be removed. It is important to remember that when it is about uPVC window repairs, do avoid the temptation to "over-caulk in order to make the area harder to clean and reduce the efficiency of your energy.

Check that any drainage holes have no debris in them and that the sill pan is properly angled to allow the water to drain from the window. In more extreme situations, you may have to replace the window.

Other indicators of water leakage are sills that are rotten and the appearance of black spots of mold on the walls near the window. This fungus thrives under damp conditions and can spread quickly throughout the house.

If the leakage occurs between the double glazed window repairs-glazed glass it is more likely that the issue is more with the seal rather than the frame. Again this can easily be corrected by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and open in a breeze It could be hinges that are at the fault. They can be repaired by any skilled DIYer and can usually be completed in a matter of minutes.

Most households in the UK will have either top hung or side hung uPVC windows that have hinges and, like all mechanical parts, they can wear down over time. The process of replacing a hinge on a window is essentially a very simple process but it can be simpler when you have a person to help hold the frame in place.

Check that the uPVC hinges open and close in the correct direction. Look for the arrows that are on each hinge to determine which direction the window should be opened.

The problem with the hinges on windows can be caused by incorrectly opening the window in a particular way or due to improper installation in the factory. This can often be resolved by sending us a photograph through our website and we will be more than happy to give you suggestions.

Regular lubrication of the hinges is also necessary. Applying an engineering lubricant that is light to the hinges is a great way to do this. We suggest using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also lower the risk of a window sticking and help prevent corrosion. Ideally, you should perform this every year. WD40 or other solvent-based lubricants should not be used as they can damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by various factors. First, the hinges because of wear and tear, can become misaligned, this will cause an opening to appear between the sash and the frame. If they're beyond repair, it might be required to realign them. In addition, the interlock could also become misaligned. This is located on the hinge side and may need to be cleaned. In some instances it is possible to replace these.

The next most common cause of draughts is the window seals, these are prone to wear or damaged over time, and allow air to escape through the gaps. Replacing these with high-quality weatherstripping will help to stop draughts. Another option is to replace the upvc window with low-emissivity glass, this will help to regulate indoor temperatures and will lessen draughts.

The final method to cut down on the amount of draughts is to use a Draught-exclusion device. These are usually fabric tubes filled with a filler, which can be placed over your window sill. They will help keep cold air out and keep your home warm and cozy!

Your windows made of upvc will keep providing excellent insulation and security to your home by performing regular maintenance and repairs. However, it is important to recognise that all windows have a life span and eventually, they will reach an point at which it is more cost-effective to replace them rather than repair them. If you are having issues with your upvc windows, it is best to seek professional assistance as soon as possible.