• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen can maneuver large panes of tempered glass from a height above the ground. They work under extreme weather conditions and follow strict safety protocols.

Wearing protective clothing, remove all glaze putty and glazing points with a utility knife. A heat gun can soften and remove the old putty.

Replacement

When a window pane breaks, it can be tempting to try and repair the glass rather than replace it. It is cheaper to replace a window, and it will also help prevent other problems in your home's efficiency. You should also take into consideration the kind of glass that is damaged to determine if it is temporary or if you'll need to invest in an alternative that is more durable.

To fix a damaged window, you must remove the frame or sash, and place it flat on the floor. Wearing eye protection, gently move the window's pane and pull out any remaining fragments. Utilize a utility blade to remove the glazing compound and the glazing points that secure the window. Keep the track of these components and their locations to ensure that they can be put back in place later.

After removing the frame and sash you can start preparing to replace the glass. Make sure that the opening of the frame is of the correct size for the replacement window. Take measurements both ways across the opening, and then subtract 1/8 inch from each measurement to give the expansion and contraction of the frame and glass. After that, you can purchase double-strength glasses cut to these exact measurements. It is recommended to also purchase enough glazier's clips, or points to place them every 6 inches around the window pane.

If the manufacturer is responsible for this then you should call them and file a claim. Once the new glass has been installed, it needs to be bedded in with a thin layer of glazier's compound. After letting the compound dry then you can paint it to match the rest of the frame.

If the crack is greater than an inch you can stop it from expanding by scoring a small arc just beyond the crack. This trick is not foolproof however it can slow the development of the crack until you are able to take permanent measures.

Repair

Professional window installers know how to handle a variety of glass and have the tools needed to complete a proper job. They also understand the best ways to dispose of waste, and are less likely to leave scraps that are left behind, which could injure family members or pets. They're also familiar with different window types, and they may be aware of issues that aren't obvious to the uninitiated homeowner.

Before you begin the process of repairing cracked window glass, ensure that you wear safety goggles and gloves. A small crack can cause shards to fly off, creating a risk for anyone living in or around the home. It is important to determine the cause of the crack, as this could prevent future problems.

Begin by creating a two-part epoxy mixture. These are usually 50/50 mix of hardener and resin, and must be quickly mixed. After the mix has been made, apply it directly to the crack and allow it to dry. It will take just about a minute however it is important to do it quickly because the mixture is very dense and quick drying.

After the epoxy has dried, you can remove excess epoxy with a blade. The next step is to scrub the cracked glass. If you don't clean the area properly, the residue could cause further damage to your glass. Make use of a putty knife to smooth the compound around the edge of your window and match it with the frame of wood.

Consider using a plastic cover for a more durable option. A trash bag that is heavy-duty or tarp is ideal, but you can also apply masking tape to the glass. This will prevent the crack from expanding, and will also block out wind, water bugs, debris, and water.

You can come up with an interim solution if you are unable to get to the window in a timely manner. Simply apply a small amount of the stuff around the outside edge of the broken pane. It won't completely fill the gap between the frame and glass however it will keep the crack in place while you fix it.

Repainting

If your glass windows are old, you may consider repainting them. This is a cost-effective alternative to window replacement and it can give your home a fresh new appearance. Before painting, make sure the surface is clean. Use rubbing alcohol or soap and water to wash away oil smudges, and other residues which can prevent paint from adhering. It is also recommended to wear rubber gloves when working on glass to avoid the risk of transferring your own oils onto the surface of the window. In the end it is recommended to apply several thin coats of paint instead of a single thick layer. This will make the paint last longer and will keep your windows looking smooth and even.

If you're planning on repainting your glass windows, ensure that you have the proper tools nearby. You'll need either a brush or sponge painter's tap along with a ruler, toothpicks and a ruler. It is also recommended to have the paint and brushes you'll be using for the project in your possession. Make sure you follow the manufacturer's directions and have a good amount of patience since it may take some time for the paint to dry.

It is also important to ensure that the room you're working in is well ventilated, especially if you're using solvent-based paint. This will lower the risk of breathing into harmful chemicals and allow the paint to dry more quickly. Also, make sure you wear a mask that is protective for any spray paints you apply.

It is necessary to clean the glass window thoroughly with soap and warm water before you paint it. Clean the glass window thoroughly with soap and warm water, then use rubbing alcohol to scrub away any grease or oil that could affect the paint's adhesion. Make sure that the windows are dry before you begin coating them.

If you have energy efficient double glazed window repairs pane windows on your windows, it might be possible to submit a claim for repair or replacement with the window manufacturer or dealer who sold them. This is especially true if your windows are still under warranty and you've had multiple problems with condensation or broken glass.

Sealing

Whether you have old double-pane windows that have a cracked seal or newer insulated glass units (IGUs) that have experienced defogging and fogging, there are a variety of options to address the issue. The most expensive option is to replace the frame and insulated unit but it may be necessary if condensation or fog is causing energy loss. Other options include replacing the IGU with a single-pane or fixing it by drilling a small hole through the bottom of the unit, and then filling the solution with anti-fog.

You can also fill in the gap between the window frame and the threshold or sill with a felt strip or vinyl V-strip. Felt can be stapled, glued, or placed in place, but is not a great protection against moisture. Vinyl weather stripping v-strip is durable and simple to install however it can be expensive and is usually used for areas that are subject to abrasions that are high. Door sweeps are able to be easily nailed to the floor and are affordable. However, they provide very little or no protection between the threshold and air.

To fix a damaged window seal make use of a putty blade to remove the old caulk. Wearing eye protection and gloves, carefully pry out the glazing points -- tiny fasteners that fix the glass in the frame's recess, with sharp edges and pointed edges. After removing the glazing points, clean out the grooves and sand the wood. Wipe off any sanding traces Then, seal the bare wood with a linseed oil based paint or clear wood sealer.

Traditional glazing putty can be applied with either a putty knife or a caulking gun. However, using a knife allows for a more efficient application that is more precise and provides a stronger seal. Make sure you choose a putty specifically designed for glass windows, as it will have higher adhesion and a longer life.

Apply a thin layer of putty across the inside of the frame where it joins the glass. Slide the window into the frame, so that the scribed line on the glass lines up with the edge of the frame. Apply pressure to the glass in order to force the putty to form a tight seal. Smooth the compound with an ungloved finger, and wipe away any caulk that was applied incorrectly or drips that have escaped before it is dry.