• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is an excellent option for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they are not susceptible to rust or rot.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will reduce repair costs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows can cause serious damage to your home and may even be fatal. It is essential to ensure that your windows are in good working order.

For single pane windows, it is relatively easy to replace windows, and the new one will usually fit inside the frame that was previously installed easily. However, if you have double-pane windows that are held in place by internal beading, it'll be more difficult to get rid of the existing panes and install new ones. In this instance, it is necessary to buy plastic spacers to help the new pane fit into the window frame.

Wearing eye protection and heavy gloves is essential if you plan to remove the glass by yourself. It is also recommended to lay down a drop cloth prior to when you start working on the glass to ensure that any shards fall on the fabric rather than on the floor where they can be trampled on and cause further damage.

Once the glass is removed from the window, it's best to seal the gap with some clear packaging tape or duct tape to block water and drafts from getting into the property until a professional can come out and fix the window repair near me. This will also act as a barrier that will prevent any intruders from gaining entry to your home. If the gap is large, you may think about an alarm door that comes with an integrated window, since it will provide the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber windows with sash. However, over time, they may be afflicted by a variety of problems including sagging. A sagging uPVC windows can cause problems with light, draughts and even security. It's important to take action as soon as you realize that your uPVC windows are falling down.

To repair a window that is sagging, you can try to reposition the hinges. First, you'll need to unblock the windows to reach the frame. With the screwdriver, you'll be able to take off the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after you have repositioned your hinges. If you're satisfied with the fit, you can tighten the screws to ensure they remain in place.

If you can't reposition the hinges you may need to replace the seal. Rubber seals may dry out and lose their elasticity with time, leading them to loose their elasticity. If this happens, it's essential to replace the seal as fast as you can to ensure that your uPVC windows remain watertight and safe from drafts.

UPVC handles can also become loose. The majority of the time, this is caused by screws that have become loose over time. However, it could be due to the fact that the handle mechanism has worn out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. First, you'll need close the window and perform an experiment to ensure that it fits. The corner joints of the sash must align with the casing joint. If it does not, you can use the screwdriver to loosen up the handle. Then, you can turn the mechanism into position.

3. Water Leaks

It is essential to take action if get up each morning to find a smoky wall and wet floors. Water leaks from windows not only lead to the degrading of the structure of your home but also undermine your efforts to control the temperature within your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or missing.

This is a fairly simple fix and should be undertaken by any competent DIYer. Depending on the severity of the issue the old caulking may need to be removed before a new layer can be put on. When it comes to uPVC repair, you must avoid 'over-caulking'. This will only make your window more difficult to clean and decrease its energy efficiency.

It is important to check that any drainage holes are clear of debris and that the sill pan is angled properly so that it drains away from the window. In more serious instances, you may need to replace the window.

Other signs of long-term water leakage are sills that are rotten and the appearance of black spots of mold on the wall near the window. The is a fungus that thrives in damp conditions and is able to quickly spread throughout the house.

If the leakage occurs between the double-glazed glass, it is more likely that the issue is more with the seal rather than the frame. A uPVC specialist can easily solve this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or loose and open in a breeze, it may be hinges that are at the fault. Anyone with the skills to fix them can replace these in a matter of minutes.

Like any mechanical component hinges are prone to be damaged over time. It is very easy to change a window hinge but it's much easier if someone helps hold the frame.

It is also worth checking that the uPVC hinges are opened and closed in the right direction. This can be done by looking for the arrows on each hinge, this shows which way the window should be opened.

The problem with the hinges on windows could be the result of incorrectly opening the window in a certain manner or because of poor installation at the factory. Sending us photos through our website can often solve the issue. We are more than happy to provide suggestions.

Regularly lubricating the hinges is essential. This can be done by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also prevent corrosion and decrease the chance of sticking. The ideal time to perform this every year. WD40 and other solvent-based lubricants are not recommended as they can cause damage to your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by a variety of various factors. The hinges may also become misaligned due to wear, causing gaps where the sash and frame meet. If they're beyond repair, it could be necessary to have them realigned. Secondly the interlock, lock this is on the hinge side of the window, can also be misaligned, and again it may be possible to just give them a clean but in some instances it could be necessary to have them replaced.

These seals can wear down or be damaged over time, allowing air escape. Replacement of these with high-quality weatherstripping will help to keep draughts at bay. Another option is to replace the upvc window with low-emissivity glass. this will help to regulate indoor temperatures and again will lessen the risk of draughts.

Lastly, one of the most effective ways to cut down on the draughts in your home is to use an draught excluder. These are typically made of fabric that are filled with some type of filler. They can be placed on the windowsill on top. They can help block out cold air and keep your home warm and cosy!

Your windows made of upvc will keep providing excellent insulation and security for your home with a little regular maintenance and repairs. It is important to remember that all windows will eventually become worn out, and it may be more cost-effective to simply replace them than to repair them. If you are experiencing issues with your Upvc windows, it's recommended to seek help from a professional immediately.