• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Kia Sportage Replacement Key

For a number of Kia models keys, there is a built-in keyless entry system. This key is similar to the remote control, and is exchangeable by an Kia dealer.

Key fobs may stop working due to a variety of reasons, including the battery being dead, worn-out buttons signal interference, or water damage. Here are some suggestions to assist you in getting your Kia key fob that is a replacement for the sportage for good.

How do you replace the remote key or smartkey

If your Kia comes with an intelligent key, remote key, push-to-start keys, or a regular non-transponder steel key The battery inside these keys will eventually require replacing. This is especially when your car shows a message that states the remote or [empty] smart keys are not powered by batteries.

This is a relatively easy procedure. To replace the battery on the keyfob take out your mechanical key from the slot at the back of the fob. Then, pry the cover open. Inside the key fob there will be a small screw that holds the battery in its place. By using a small screwdriver take the screw off and pull out the old battery. Then, insert the new and close the hole in the key fob.

When the key fob is equipped with new batteries check it by pressing the lock and unlock buttons. It's good when the doors lock or unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you need to run errands around Brandon.

Note: Some key fobs could need to be programmed (transponder chips or smart keys). This requires a machine for programming, which is only available to the locksmith for cars or dealer. Other keys (non-transponder metal keys) don't require programming. If you want to change the programming of your key, [Redirect-302] you'll need to note the key code's number on the tag for the key code.

How do I replace the battery?

If your Kia key fob is not responding to pressing the lock or unlock button on the fob, it is a signal that the battery needs to be replaced. A weak battery can cause other issues, such as the check engine light flashing on or a delay in cranking the engine. It is relatively easy to replace key fob batteries by using only a few simple tools.

Make sure that you shut off your vehicle and shut all doors prior to beginning. Locate the small plastic piece on the bottom of your key fob and play with it until a metallic key pops out. You can then insert the key into the handle of the door for the driver to open your car.

To replace the battery inside the key fob remove the cover on the rear. Make use of a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and then orient the replacement battery so that its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid bending or damaging the contacts of the metal.

After you have installed the new battery after which you turn the key fob on and off in the ignition until the door locks up. Then, you can test your Kia key fob to see whether it's working again.

How can you replace the smart key

There is a possibility of having a standard keyfob or a Smart Key based upon the model of 2013 kia soul key fob Sportage. The difference between them is that the smart key is equipped with tiny mechanical key blade that is hidden inside, while the standard key fob does not. Both key fobs come with an internal battery that will eventually need to be changed. It's an easy process that will take about two minutes.

Before you begin before you begin, ensure that you are on a flat surface with sufficient lighting and that your Kia is not on. Be aware that there are small parts inside the fob that could be snagged if not cautious.

The small release button is located on the lower backside. It's either a circular or rectangular slot. When you press it mechanical key blade, it will pop out and you can then open the key fob.

Once you have the key fob opened it is easy to take out the old battery and replace it. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. When you are done you should be able to lock and unlock your car with your key fob even if your engine isn't running!

How do you replace a mechanical key

The Kia keyfob is a great convenience that lets us lock or unlock our car by simply pressing the button. As with all devices that is used, the Kia key fob can have issues at times. Luckily, there are ways to resolve these issues and keep our key fobs in good working condition over the long haul.

One of the most common problems is a weak or dead battery. This can cause your fob to stop working or operate intermittently. If this is the problem it is time to replace the battery a new one.

If this doesn't solve the issue, try using a flathead screwdriver standard to push the fob's casing made of plastic open. Be careful not to damage any internal components, or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a new one.

Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob to confirm it's functioning correctly. If the fob isn't working, call a locksmith or dealer to solve the issue. Make sure they make you an emergency key that functions in all the trunk and door cylinders in order to avoid lockouts again.