• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen work high off the ground, maneuvering huge glass panes. They work in extreme weather conditions and adhere to strict safety guidelines.

Wearing protective clothing, take off the metal glazing points as well as the glazing putty by using a utility knife. A heat gun may help soften the old glue and speed up removal.

Replacement

It's tempting to fix the glass on your windows instead of replacing it if a pane breaks. It is more cost-effective to replace a window and it can also help you prevent other problems in your home's efficiency. You should also consider the kind of glass that is damaged to determine if it is a temporary fix or if you will need to invest in a more permanent solution.

To fix a damaged window, remove the frame or sash, and lay it flat on your work surface. Wearing eye protection, carefully wiggle and pull out any shards that remain in the window. Use a utility blade to cut off the glazing compound, as well as the glazing points that keep the window in place. Keep the track of the components and where they are so they can be reinstalled.

After you've removed the frame and sash, you can start preparing to replace the glass. Before you do so, make sure that the opening in the frame is properly size for the replacement window. To allow for frame and glass expansion and contraction, measure both directions across the opening and subtract 1/8 inch. Then, buy double-strength glasses that are cut to these exact dimensions. It is also recommended to purchase enough new glazier's clips or glazier's points to be placed every 6 inches around the window pane.

Depending on the window's warranty it could be covered by the manufacturer and in this case, you must contact the company to file an claim. Once the new glass is installed, it should be covered with a thin layer of glazier's compound. After letting the compound dry, you can paint it to match the frame of the window.

If the crack is greater than an inch you can stop it from spreading by slicing an arc that is just a little beyond the crack. This trick won't be completely foolproof, but it could slow the development of the crack to a manageable amount until you can take permanent measures.

Repair

Professional window contractors know how to handle a variety of glass and have the tools needed to complete an excellent job. They know how to dispose of waste in a safe manner which means they are less likely than other people to leave behind scraps that could harm family pets or members of the family. They're also familiar with different window types, and they may be able to spot problems that might not be apparent to a homeowner who isn't experienced.

Wear safety goggles and gloves before you begin repair work on cracked glass. Even a small break can cause shards to fly, creating a risk for anyone in or around the home. It's important to determine the cause of the crack, since this will help prevent any future issues.

Create a two-part mixture of epoxy. They are usually made up of a 50/50 mix of resin and hardener and must be mixed quickly. Once the mixture has been made then apply it directly to the crack and let it dry. It should only take about a few minutes, but you must work quickly because the mixture is very thick and drys very quickly.

Once the epoxy has dried, you can take off excess epoxy with a putty blade. Then, you'll need to clean the area around the cracked glass. If you do not clean the area properly, the debris could cause further damage to the glass. Use a putty blade smooth the compound around the edge of the window and then match it to the frame made of wood.

For a more durable solution think about using a plastic covering. A trash bag that is heavy-duty or tarp is ideal, however you can also use masking tape to cover the glass. This will stop the crack from spreading, and will also keep wind, water and bugs out.

You can create an interim fix in the event that you are unable to access the window in time. Simply apply a small amount of the material around the outside edge of the broken pane. It won't completely seal the gap between the frame and the glass completely, but it will hold the fracture until you are able to repair it.

Repainting

If your glass windows are old, you might consider repainting them. This is a low-cost alternative to replacing windows and give your house a new look. Make sure that the surface is clean before painting. Use soap or rubbing alcohol and water to wash away oil smudges and other residues which can prevent paint from adhering. Wear rubber gloves when working on glass surfaces to prevent transferring oils from your hands onto the surface. Apply several thin coats instead of a single thick one. This will allow the paint to last longer and will keep your windows looking smooth and even.

If you're planning to paint your glass windows, make sure you have the appropriate tools nearby. You will need brushes or sponges painter's tap along with a ruler, toothpicks and a ruler. You should also have the brushes and paint you'll be using to complete the project. Follow the manufacturer's directions. Be patient as it can take some time for the paint to fully dry.

If you are using solvent-based paint, you should make sure that the area where you work is adequately ventilated. This will reduce the chance of inhaling toxic chemicals, and the paint will dry more quickly. Use a protective mask when using spray paints.

It is necessary to clean the glass window repairs near me thoroughly with soap and warm water before you paint it. Clean the glass window thoroughly using soap and warm water. Then, use rubbing alcohol to scrub off any oil or grease that could affect the adhesion of the paint. Make sure the windows are completely dry before you begin to paint them.

If you have energy efficient double pane windows on your windows, it might be possible to submit claims for repair or replacement with the window company or the dealer who sold the windows. This is especially true if your windows are still under warranty and have experienced several issues with condensation or broken glass.

Sealing

There are a variety of options to fix the problem, whether you have an old double-pane window that has cracks in the seal or if you own an upgraded insulation unit (IGU) that has experienced defogging. The most costly option is to replace the frame and insulated unit however it could be required if fog or condensation cause energy loss. Other options include replacing the existing IGU with a single-pane, or repair it by drilling a small hole through the bottom of the unit and then filling the solution with anti-fog.

You can also fill in the gap between the window frame and the threshold or sill by using a felt strip, vinyl v-strips, or a door sweep. Felt is inexpensive and can be glued, nailed, or stapled into place however it doesn't offer much protection against moisture. Vinyl v-strip is easy to put up and is durable however it can be expensive. It is generally reserved for areas exposed to abrasions that are high. Door sweeps are easy to nail to the floor and are affordable. However, they offer little or no protection between the threshold and the air.

To repair a damaged window seal, use a putty blade to scrape off the caulk. Wearing gloves and eye protection, pry out the glazing point -- tiny fasteners with sharp, pointed tips that pin the glass into the recess of the frame. After you have removed the glazing points, clean the grooves and sand the wood to a smooth finish. Wipe off any sanding debris and then seal the unfinished wood surface using a linseed oil-based paint or clear sealer.

Traditional glazing putty can be applied using the help of a putty blade or caulking gun, but a knife provides a better, more precise application and creates a better seal. Make sure you choose a putty specifically designed for glass windows, as it has better adhesion and long-lasting.

Apply a thin layer along the inside edge of frame where it joins the glass. Slide the window into the frame in a way that the cut line on the glass aligns with the frame's edge. Apply pressure to the glass to press the putty and glass into a tight seal. Smooth the compound using an ungloved finger and then wipe off any mistakenly applied caulk or drips that have escaped prior to drying.