• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace Window pane Window Panes

A damaged window pane can be a nuisance. This can be an opportunity to upgrade your windows to energy efficient or insulated ones, and reap benefits like increased comfort, increased resale value and reduced utility costs.

You can do it yourself for a only a fraction of the cost it would cost to hire an expert. It requires the right tools and an hour or two of your time.

Glass

Replace your old single-paned windows with tempered or insulate glass to improve the efficiency of your energy, reduce noise, and maintain the historical integrity of your old home. The replacement windows near me of a window pane is relatively easy and can be accomplished by anyone with basic hand tools. You will also need a replacement window pane, glazier's tips, pliers, and latex glazing putty. If you need to you may use a heating gun to warm the old putty. Before starting, wear protective gloves and goggles since working with broken glass could cause injuries.

Begin by removing any remaining broken pieces of glass. It is recommended to use pliers however, a flathead may work equally. After that, use a wood chisel or putty knife remove the remaining old putty from around the frame and the sash. Be careful not to damage the window sash. Be careful and slow. It is a good idea to do this on a sturdy ladder rather than on the ground, and to have someone stand below the sash to help keep it in place.

After you've removed all the old putty, prepare the window frame to fit the new pane. Measure the width and height of the sash opening and subtract 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be taken to an hardware or home centers store to have an item cut from stock glass to the right size. Alternately, you can cut the glass yourself, if you have the appropriate tools.

After installing the new pane After installing the new pane, apply a small amount of caulking around the edges to make it weatherproof. Install a glazier's pointing on both sides of the frame. This will ensure the pane. The points shouldn't be so tight that they cause friction between the sash and frame however they should not be too loose.

Before applying the putty to the surface, gently knead it until it is soft and free from lumps. Roll it into pencil-sized strips. Place the first strip in the corner of the frame, working from one corner to the other to ensure it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of metal that help secure the glass into the window frame without causing damage to the delicate surface. It's easy to learn how to use this nefarious tool, and you'll be able to save money on the cost of an installation by a professional.

After removing the old putty, glazier points, and any other residue, clean the frame thoroughly using a utility knife. If needed you can lightly sand the wood along rabbet grooves to smooth out rough areas. If you sand wood cover it with painter's tape to prevent accidental damage.

Take measurements of the empty frame and record precise measurements. Bring these measurements to a hardware store or home center and have the new pane cut slightly smaller than the frame's opening. This will ensure a secure fit and will allow room for expansion and contraction.

Place the new window in the frame and push it into place firmly using your hand. Then, you can use the point of your chisel or the back of the putty knife to tap in the glazier's points as shown in Figure 11. After you're done, the points should be in line with the top edge of the pane, and the shoulders that are raised of the points should be just below the rabbet's rim groove.

Apply a thin layer glazing compound on the rabbet grooves and the edges of new glass. This will protect and seal the edges. Allow it to dry and cure completely.

Install the new window sash once the glazing compound has dried. First, coat the wood with a thick coat of Linseed oil. This will stop the new putty from drying out and cracking when it absorbs moisture. Apply the coat using a brush or the edge of your putty knife, and then use the chisel, or the back end of the knife to gently press the new sash and glazier's tips into the grooves of the rabbet. Repeat this process in intervals of 10 inches all around the frame.

Putty

A baseball thrown, a rock thrown in error, or a tree falling could result in a broken or cracked window pane. The majority of windows can be replaced by simply putting in a fresh piece. The glass is held in the position with a tiny metal clip, referred to as a glazier's point and putty. This compound is also called glazing compound. Remove the old pane and clean the area with the rag, a pull-type scraper or wood chisel. Wear gloves and safety glasses while doing this work. You'll require a heat gun when the window is fixed into the frame.

If you're planning to reinstall the original sash, take off the molding that holds the old pane. Sand the sash until it is flat and ready for new caulk. Once the sash is installed it is possible to apply a silicone caulk on the glass. This will ensure that it doesn't be leaking or fade over time.

Remove the glazing points from the rabbets, or the grooves in the sash that the glass sits. If they're difficult to cut out, try placing a hand tool like a heat gun over them to soften them before you do. If you're using a heating gun, be cautious not to cause damage to the sash or its railings by placing the tool too close.

After the old glazing points and putty have been removed, prepare a bed for the new pane. Roll a piece of glazing compound between your hands, shaping it to be about 1/2-inch thick. Press it into the rabbets, where the glass will be put. The glass must be positioned against the putty on both sides. If needed you want to tap your glass lightly into the rabbet with your thumb.

If the new pane is cracked then you can seal it with a solvent-based glue or silicone caulk before pressing it into the sash. If not, you'll have to putty over the crack to create a tight seal and keep water out. Once the putty is dry remove the oily film off the glass and allow it to dry completely before you paint. If you paint before the putty has completely dry, it won't create an effective seal and could be leaking or discoloring over time.

Paint

If you've had a broken window pane, you may be worried about the cost of a new one. It's true that replacing a single piece of glass doesn't need to be costly when you do it on your own. Even double-paned windows can be replaced for a fraction of the price it would cost an expert.

If you are working with a large glass window, first make sure it is securely attached to the frame. This can be done relatively easy and fast using the appropriate tools and techniques.

When you are ready to start, remove the old window pane. Remove the metal glazing points that are attached to it. They are basically tiny metal triangles which function as "nails" which hold the window in place within the frame of wood. They are submerged under a bead of glazing putty, which is then cured to form a solid, moulded wedge that secures the window in place and hides the edges.

After taking off the old pane clean the frame and the wood. Scrape away any paint and sand down the rabbet grooves, where the glazing points used to be. Sand them down to bare wooden surfaces so you can paint the frames with the same color. After sanding, apply a layer of flax oil on the wood that is not sanded down to extend the life of the frame.

The next step is to determine the size of the window's opening. You'll need to take vertical and horizontal measurements of the entire opening as well as the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure that you get a precise size for the new pane. This will allow for seasonal changes in the glass. Take these dimensions to your local hardware or home improvement store, and they will have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.