• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are your first protection against unauthorised entry into your home. Signs of wear and tear, as well as instances like moving into a new residence or burglaries, could trigger the need to replace your lock.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will help you select the appropriate lock.

Deadbolt

Installing a deadbolt is great way to secure your door from intruders. The bolt extends into the strike plate on the door frame when it's locked, making it much more difficult for a burglar to break in through the door. A single cylinder deadbolt can be activated using a key on the exterior side and a thumb turn piece on the inside. Deadbolts can only function only if it is correctly installed.

First, you'll need to determine if the door already has a hole to install a deadbolt or if it needs to be bored out. With the template included with your lock installation kit, mark the location of the hole for the deadbolt on the door's surface. Then, use your tape measure to determine how to replace a lock on a upvc door high the deadbolt should be. Then, mark the high point on the outside of the door and use a speed square to draw a straight line across the mark you made for the bolt hole.

Then, use a drill to drill this spot until the hole extends to the opposite side of the door. This may take some time. Then, sand the hole and along the edge of the door until it is smooth. At this stage, it's a great idea to stain or paint your door.

When the door is in place, remove any screws visible on the existing deadbolt. This will reveal the front and rear assemblies of the deadbolt and its bolt inside. Then unscrew the old bolt and replace it by an alternative bolt that matches your door hardware. You will need to unscrew the bolt from a setplate. After that, you'll have to chisel the surface of the door frame to accommodate the strike plate.

If your strike plate is misaligned, it's likely because the previous installer didn't correctly mortise it or a weatherstripping was installed and changed the strike position. It is necessary to re-mortise the strike plate and possibly even the deadbolt to correct this problem. After this is done check the deadbolt by closing and locking it. Make sure the bolt is extending into the strike plate then test the key to make sure it closes and opens effortlessly.

Knob

It could make your home or business less secure when the door knob is worn. It may also make it harder to open or close the door, so it's an ideal idea to Replace Door Lock the knob. It shouldn't take you longer than 30 minutes. Make use of pliers or a screwdriver to remove any old knobs or handles. Be cautious not to harm other components of the door.

Before you start, you'll want to spray WD-40 or a different dry lubricant onto the mechanism of the door knob. This will assist the new lock to slide smoothly as you turn it. It is essential to choose a quality knob and handle that match your current doors to ensure that the lock is operating properly. If you don't have a matching doorknob then you'll have to purchase a replacement.

Before you begin replacing lock in upvc door the knob, examine the old knob to determine what screws are holding it in place. If there aren't any screws you can use a screwdriver to insert between the cover plate and the hidden screws plate and pop it off.

After you've removed the knob, check it for indications of damage or rust. You'll need to clean it off if you notice any marks or dents, but you shouldn't have to do anything If the knob is in good condition.

Install the new knob. First, examine the knobs you've chosen to ensure that you're selecting the correct one for your door. You'll need to choose one with an extending rod that locks with the rod mechanism of the other knob. After you've placed the new knob over the door's hole and then carefully place it in the latch.

Thread the latch plate screws down and then test the spring by pushing down on it several times. The latch should spring up each time. Install the second knob and lock it to the rod mechanism of the first knob. Attach the other long screws from the knob's interior through the cylinder hole on the doorknob on the outside and lock it in place.

Latch

A latch is a steel piece that extends into the upvc door locking mechanism replacement jamb to keep it shut. The latch can be operated by a knob or handle located inside the door, or by a thumb-turn on the outside. The latch can be secured using deadbolts to prevent intruders from breaking in through the door's glass. It also provides protection from accidental or intentional closing of the door by children or pets. A latch can be installed using single cylinder deadbolts or double cylinder deadbolts, depending on the security level you prefer.

Installing a latch involves the same steps as installing a deadbolt, however there are some distinctions. To make sure that the new lock will work, first take a measurement of the setback on the doorjamb using a tape measure. The setback is the distance between the edge of the doorjamb to the middle of the hole that will be used for the faceplate for the latch. Setbacks for standard latches are 2 3/8 to 2. 3/4 inches. If you have a higher setback, you may have to purchase a more substantial latch from a hardware store or locksmith.

Then, make a hole for a latch plate in the doorjamb's edge. Utilize a chisel to make the mortise for the latch. Make sure the hole's depth is enough for the faceplate to be in line with the doorjamb. Tape the strikeplate to the doorjamb to ensure it's placed properly.

If the strike is placed too high, the door may be pushed into or pressure imposed on it using a crowbar, or tire iron. This can also cause the doorjamb's to crack. This can be repaired by drilling a new hole into the doorjamb, then removing the core from the previous one.

Installing the new strike plate is the last step. This can be accomplished by screwing the new plate into the existing screwholes. Then, use wood putty to fill in the old screw holes and the bolt hole that won't be used. After the putty has dried then sand it to a smooth finish for a professional finish.

Strike

The piece of metal that connects the deadbolt and latch when the door is closed is an electric strike. It is an essential part of the lock's overall security, as it prevents the door from opening and provides an additional barrier to force or kick. If a door is equipped with an electronic strike, it will be opened by using keys and the control unit that regulates its electrical impulses.

Traditionally, installing an electric strike meant cutting a small portion of the doorjamb in order to release a cylindrical lock's latchbolt from the pocket of the strike. This change can be an issue in terms of the aesthetics of an opening, and it also exposes the latchbolt and keeper mechanism to unintentional users.

Recently, a number of electric strike manufacturers have developed an innovative type of electric strike dubbed the "No Cut" strike that doesn't require an opening in the doorjamb for operation. These strikes have a unique design to allow the latchbolt and keeper to slide into the strike pocket without marring the faceplate of the doorjamb.

The strike has an internal ramp that lifts the latchbolt and keeper when it receives an electrical signal from a reader or controller. The latchbolt and keeper are pushed up the ramp by the retract. When the door is shut, the deadbolt remains retracted, and the latchbolt retracts into the keeper.

Installing an electric strike can be a simple process, especially in the case of replacing a strike on an existing door. However, if you are upgrading to an electric strike for an access control system, you will need to make sure your new system is compatible with the kind of lock you have installed. You will also need to ensure that the strike is properly connected to your access control system and that it is designed to operate in a fail-safe manner.

Upgrade your strike plates with heavy duty strike plates to prevent unauthorized entry. The plates utilize four to six three-inch screws instead of the two three-fourth inch screws typically used in regular strikes. The longer screws make breaking the frame to reach the piece that turns the thumb on a single cylinder deadbolt more difficult.