• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Changing your door lock is a simple and inexpensive way to increase the security of your home. However, the procedure isn't for everyone. It requires some expertise and perseverance.

The cylinder is contained within the knob's body. The cylinder is what recognizes the key when it's put into the lock.

Take off the lock that was previously used.

First, you must remove the lock you have been using for a while. This is a relatively simple process, but there are some things to keep in mind. First, make sure that your new lock is the correct size for your door. This will ensure that it fits properly and does not leave a gap around the latch or deadbolt plug.

Once you have removed the latch plate, look for two screws or bolts on the inside of the casing, which connect the casing and halves of the lock. Remove these screws with the help of a screwdriver, and then remove the lock out of the door. If you have a mortise lock, there could be a set screw located at the base of the handle that binds it to the spindle. Use a screwdriver to remove the screw, and then take out the doorknobs.

You should also remove the deadbolt latch and latch plug from the hole in the door jamb. Install your new lock. If you're replacing a mortise you should determine the distance between your lock case and your door's edge to make sure that the new lock will fit.

There are a variety of reasons that could prompt you to change the door lock, for instance being concerned that someone else may have the key, or you are welcoming an incoming roommate. You can save money if you take the lock off yourself instead of hiring a professional. It is much easier than most people imagine and can be done in just a few moments.

Start by taking the handle and trim from your door. Then, pull the trim loose using a flat screwdriver. You should be able to twist off the majority of it. In some cases you might be able to take off the handles completely. Then, check the handle for a small pinhole on the interior side and insert a straightened clip into it. This will trigger the release mechanism and allow you to take the handle from the door. The next step is to look at the inside of the lock for another small tab that you can press with a flat screwdriver. Once the spindle is removed, you can take off the cylinder and housing.

The choice of a new locking system

There are many options to choose from when it comes to selecting a new lock. Take a look at the various types of locks and pick one that fits the style of your door. Consider the backset, which is the distance between the edge and the middle of lock hole. Also, think about the cross bore, which is a small hole in the middle of your window door lock repair frame. Select a lock that will fit the door's thickness and swing.

The American National Standards Institute and BHMA have graded all upvc window lock repair near me locks repair near me (click through the next article) for doors to give you an idea of their longevity and how difficult it is to pick them up or disable them. A grade 3 lock may be perfect for a quiet apartment complex in the countryside, whereas upvc windows locks repair that are grade 1 might be more suitable for a busy street near a storefront.

Most smart door locks require a digital code to open. If you are worried about hacking, or other security issues, talk to a professional locksmith.

Replacing the cylinder

If the cylinder of your door lock is broken or damaged, you can replace it within a matter of minutes by completing a do-it-yourself project. It is crucial to choose the correct cylinder and follow all instructions. The first step is to remove the knob or handle in the event that one is present then loosen the trim around the base of the lock cylinder using the aid of a screwdriver. After the trim is removed, you can take off the screws holding the cylinder with the flathead. The cylinder is then gently pulled away from the door.

Before installing the new cylinder, you must make sure that it is the correct length for your door. With a tape measure, measure the distance between the cylinder's center and the left and right sides. Then, purchase an additional cylinder using the same measurements. This will stop the cylinder from snapping, which can happen when the door is kicked out or when the key is stuck inside.

Place the replacement cylinder inside the door, and then turn the key. This will align the cylinder with the carriage which is located usually on the outside of your lock. You can then loosen the set screws which should be a couple of turns in the head. It is also necessary to loosen the screw at the door's edge which secures the case if there is one.

You can replace window locks upvc the cylinder that was used to lock your old lock with a new one by sliding it into the case and tightening the set screws. You must also install the part that connects the cylinder to the lock indicator stem, which you can do by pulling out three small tabs on back of the cylinder using needle-nose pliers. Then, you can attach the second bracket to the back of the cylinder. Then, you must reinstall the strike plate and latch plate as well as the retaining ring attached to the top lock cylinder.

Installing a new lock

Start by measuring the width of your door if you are replacing window locks an existing lock. Most residential locksets have a thickness of 1 3/8 to 1 3/4 inches. If your door is thicker, you will need a thick door kit that includes longer screws and an extended tail piece (for door knobs) or spindle extension (for deadbolts).

Most locks come with a detailed instruction manual to help you install the new hardware. Take the time to read the instructions before beginning the process to ensure that you've followed all of the necessary steps. The guide will give you a clear idea of how much skill is required to finish the task. You might want to ask a person who has worked with locks for assistance if you are changing a lock the first time.

Before installing the new lock it's recommended to tape over the openings of the old hardware. This will stop the screws from slipping out of the holes and will safeguard any tile you may have put in the area. This will also protect your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with an ad-hoc strip of masking tape or gaffer tape, however you can use any tape you have.

Once you've removed the screws that connect the inside of the lock section to the exterior side, pull it straight away. This must be done quickly to avoid the lock from closing accidentally and damaging the mechanism.

Install the new latch bolt in the upper cross bore of your new lock, if it comes with one. Be sure to put it in the right position as marked by an arrow on the faceplate. Then, you can screw the latch plate onto the bolt.

Finally, screw in the deadbolt and strike plates to the door jamb. Test the deadbolt by throwing it a few times to verify that it is extended all the way through the strike plate and is secured. Follow the directions included in your electronic smart lock to program it. This involves downloading an application and registering your e-mail address, verifying your identity and connecting to the wireless network in order to add your device.