• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Change of the door lock is an easy and inexpensive way to improve your home security. However, the procedure isn't for everyone. It requires a certain amount patience and expertise.

The cylinder is inside the knob body. The cylinder is what recognizes the key once it's inserted into the lock.

Remove the old lock

The first step in replacing a door lock is to take out the lock that was previously in use. It's a simple process, but you should keep some things in your mind. Make sure your new lock is compatible with your door. This will ensure that it fits securely, and doesn't leave a gap at the latch or deadbolt.

After removing the latch plate, you will have to look for two bolts or screws in the casing's interior that hold the casing in place with the two halves of the lock. Unscrew them using a screwdriver and then remove the lock from the window door lock repair. If you have a mortise lock there might be a set screw located at the base of the handle that binds it to the spindle. Remove the doorknobs by unscrewing this screw with a screwdriver.

Remove the deadbolt and latch plug from your door jamb. Install your new lock. If you are replacing a mortise lock you should also measure the distance between the lock case and the door's edge to ensure that your new lock will fit.

There are a variety of reasons that could prompt you to replace the door lock, for instance suspecting that someone else has the key or welcoming a new roommate. You could save money if you remove the repair window lock yourself instead of hiring for a professional. It is much easier than people think and can be done in a matter of minutes.

Begin by taking the trim and handle from the door. Then, you can pry the trim loose using a screwdriver that is flat. You should be able to twist off the majority of it. In some instances you may be able to take off the handles completely. Then, check the handle for a tiny pinhole on the inside and insert a straightened paper clip into it. This will trigger the release mechanism, allowing you to take off the handle. Then, look for another small tab on the interior of the lock and press it with a flat screwdriver. Once the spindle is removed, you can remove the cylinder and the housing.

Selecting a new lock

You have many options when it comes to choosing a new lock. Look at different kinds of locks, and find one that matches your door's style. Think about the backset which is the distance between the edge and the middle of lock hole. Also, consider the cross bore, a tiny hole that is located at the edge of your door's frame. Select a lock that is suitable for the door thickness and swing.

The American National Standards Institute and BHMA have graded most door locks to give an idea of their strength and how difficult it is to pick them or disable them. A grade 3 lock might be ideal for a quiet rural apartment complex, while an entry grade lock could stand up to the traffic at a busy storefront on a busy city street.

Most smart door replacement window locks require digital code to open. If you're worried about hacking or other security concerns you should consult a professional locksmith or your local police department to get advice.

Replacing the cylinder

If the cylinder of your door lock is broken or damaged, you can replace window lock it in a matter of minutes by completing a do-it-yourself project. It is essential to choose the appropriate cylinder and follow all instructions. First, take off the knob or handle, if it is present. Then, using a screwdriver, unscrew the trim that surrounds the lock cylinder. Once the trim is removed, you can reach the screws that keep the cylinder in place and remove them using a flathead screwdriver. The cylinder is then gently removed from the door.

Before installing the new cylinder, be sure that it's the right length for the door you are using. Take a measurement of the distance from the center to the left and right sides of the cylinder using an instrument. Then, purchase a new cylinder with the same measurements. This will prevent the cylinder from snapping, which can happen when the door is kicked in or when the key gets stuck inside.

Install the replacement window Locks cylinder into the door and then turn the key. This will align the cylinder with the carrier which is typically on the outside of the lock. Then, you can loosen the set screw that is supposed to be a few turns in the head. Also, you will need to loosen the screw at the door's edge which secures the case if there is one.

After removing the lock cylinder, you can replace it with the new lock by slipping the new cylinder into the case and tightening the set screw. You should also reinstall the piece that connects the cylinder to the stem for the window lock repair cost indicator and this can be done by removing three small tabs on back of the cylinder using needle-nose pliers. Attach the bracket that is smaller to the back of the cylinder. Then, you need to put back in the strike plate and latch plate, as well as the retaining ring that is connected to the top lock the cylinder.

Installing a new lock

If you're replacing an old lock, start by measuring the width of your door. Most residential locksets have a thickness of 1 3/8 to 1 3/4 inches. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll need a stronger door kit. This will require longer screws and either a longer spindle extension or the tail piece for door knobs.

Most locks come with a thorough installation guide to assist you. Before you begin, go through the instructions to ensure that you've followed all the steps. The guide will give you a good idea of the level of skill that is required to complete the task. You may want to ask a person who has worked with locks for assistance if are changing locks for the first time.

It's a great idea to seal the openings of the old hardware before installing the new lock. This will stop the screws from falling through the holes, and also protect any tiles you may have installed. It also helps prevent potential damage from rust grime, dirt and. SECURAM Touch includes the masking strip or gaffer tape, but you can use any tape you own.

After you have removed the screws that hold the lock's interior to the outside, take the lock off immediately. This should be done swiftly to prevent the lock from accidentally closing and damaging the mechanism.

If your new lock has an latch bolt, install the new bolt into the upper cross bore. Make sure you put it in the correct position, which is marked by an arrow. Then, slide the latch plate onto the bolt and screw it in place.

Finally, screw the deadbolt and strike plates to the door jamb. Test the deadbolt a few times by throwing it to see if it extends into the strike plate. If you're using an electronic smart lock, be sure to follow the instructions to program it. This involves downloading an application, registering your email address, verifying your identity, and accessing the wireless network to add your device.