• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

Over time the handles on your doors will get worn out and need to be changed. It is essential to keep the same dimensions as the handles that were previously used when replacing them.

The three measurements you need to examine are the top screw's position, lever and key hole sizes. Refer to the size guide for assistance in this.

Inline Lever/Lever

A lever handle is a modern-day door handle that is designed to fit new or replacement doors. This type of door handle is available in a variety of styles & finishes. A variety of manufacturers provide this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The handles made of uPVC/Composite are made from durable materials, and are ideal for multi-point lock doors that require a strong design. The window handles are inline and use the same screws and spindle to secure them. They can be easily mounted on a new or existing uPVC/Composite door.

The handle can be adjusted and angled to suit the needs of all users. The handle has been tested to 200,000 cycles, this allows for the assurance of the quality of the finish and the performance of the handle over time. The lever that springs is adjustable to fit a wide range of locks. This is particularly beneficial in doors with smaller door frames where the cylinder is located further back. A lever that is shorter is a good choice for doors where the latch could be operated by a thumb turn on the inside.

Lever Pad

A Lever Pad upvc door handle operates differently to the lever type handles found on most doors. These handle types can either operate from a single spindle (inline) or independently from both sides using two offset or inline spindles (pad). They are usually used on UPVC double glazed doors. They are available in a variety of variations and styles.

The handles are available in a variety of finishes, including White, Chrome and Gold. The finish is in line with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, thereby giving the handle a high level of durability and performance for the intended use.

All UPVC levers for handles include a spindle and screws and can be installed on the uPVC door. The backplate fixation centres of 211mm allow for a wider handle, which is often an advantage when replacing a damaged or old upvc door handles multi-point door lock mechanism. The handle levers come with springs, which eliminate the problem of handles for doors that slide out of horizontal position when not in use.

It is essential to match up the PZ dimensions for both the multipoint lock and the uPVC doors when selecting the replacement UPVC spindle and handle. This measurement is often called the "handle centre" or "cylinder centres and is an essential aspect to match the appropriate handles.

After you have determined the correct size of PZ it is important to make sure that the push and lever pads are shaped to match the American with Disabilities Act compliant handles that you need for your door. These are typically square or round with an internal lever, and an external push pad.

The majority of the UPVC Lever Pads that we offer are spring-loaded. This means that they return to a horizontal state when not in use, rather than hanging and possibly securing to the frame. This stops draughts from entering the home. The majority of UPVC lever pad style handles come in both left and right handed versions which allows them to be installed on either side of doors.

Euro Cylinder

Cylinder locks can be found on uPVC and other types of doors. Cylinder locks are operated by using a key that unlocks the cylinder case. This reveals pins that can be aligned to those in the lock and allow them to turn the camera that rotates, opening the door. Euro Cylinders can be fitted with up to six pins, with both internal and external doors usually needing different levels of security.

Choosing the right cylinder is crucial; it depends on the way your door and handle are used. For instance, doors that are external require a higher security cylinder, whilst internal doors can be secured using a standard cylinder. Certain cylinders are equipped with additional features that increase security, for instance, anti-drill or anti bump properties.

To ensure that the euro cylinder is the correct size for your door, it must be measured accurately. The cylinder needs to be measured from the screw hole in the center to the ends of the cylinder. This includes the thumb turn, if there is one. It is recommended to do this with the lock in place however in the event that this is not possible, you can take it off to measure. A cylinder that protrudes beyond the handle and escutcheon might be susceptible to attacks like snapping locks, therefore it is crucial that it is not too long.

The design of most newer cylinders comes with anti-drilling as well as bump resistance features. They are designed to decrease the chance of attack by forcing cylinders to turn in a different direction. This will help to deflect an attack and keep your door safe.

Certain cylinders are made to resist snapping. This is a common attack on cylinders. A specific tool is used to break the break line of the lock and then the front of cylinder is snapped off. This is faster and more straightforward than opening the door with a multipoint lock and leaves no evidence of a burglary, which can hinder an insurance claim.

Spring Cassette

The spring cassette is located in the base of your door handle's backplate, supplying a spring-loaded solution to return the multipoint lock handles back to their rest position after usage. In the past, a lot of these types of window handle repairs didn't have a spring built into them, and as a result, they can droop or drop once the locking mechanism is removed. Adding this simple component is among the best ways to correct this, and is an effective way to keep your doors made of upvc from becoming stuck in either closed or open position, as they aren't always easy to close manually.

These spring cassettes are specifically designed to be used with multipoint locks that are sprung, they will not fit non-sprung multipoint handles. You will need to have a hole specifically cut in the backplate to allow them to fit (please check the image for a technical diagram). These cassettes can be used as a replacement for damaged or missing cassettes on the backplate of uPVC aluminium door handles handles. They are supplied in a single unit. They come with a square cut out that is able to accommodate an 8mm shaft.

These spring cassettes provide an excellent value solution for the issue of door handles that are sagging. These spring cassettes are simple to install and can extend the lifespan of your uPVC door. Contact us for more information about our selection of uPVC accessories and spares. We are here to assist and offer expert advice.