• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock change is a quick and cheap way to improve your home security. This isn't for everyone. It requires a certain amount of patience and skill.

You must replace the cylinder, which is located within the knob's body. The cylinder is responsible for recognizing the key as it is put into the lock.

Take off the lock that was previously used.

The first step to replace a door lock is to remove the old lock. This is a relatively easy process, however there are a few things to be aware of. Make sure the new lock fits the door. This will ensure that it fits snugly and doesn't create a gap around the deadbolt plug or latch.

Once you have removed the latch plate look for two screws or bolts on the inside of the casing, which hold the casing and the two halves of the lock together. Remove these screws using a screwdriver before removing the lock off the door. If you have a mortise lock, there may be a set screw located at the base of the handle that binds it to the spindle. Remove the doorknobs by unscrewing the screw using a screwdriver.

Remove the deadbolt as well as the latch plug from the door jamb. Then, you are able to install your new lock. If you are replacing a mortise upvc window lock repairs you must also measure the distance between the lock case and the edge of your door to ensure that your new lock will be able to fit.

You might want to change your lock for a variety reasons, such as when you suspect that someone else is holding the key or if you've got an incoming roommate. You could save money if you take the lock off yourself, instead of hiring for a professional. It's easier than many people imagine, and it can be completed in a few minutes.

Start by getting rid of the handle and trim from the door. Then, you can pry the trim away using a flat screwdriver. You should be able twist off the majority of it. In some cases, you may even be able to remove the handles completely. Then, check the handle for a small pinhole on the interior side and insert a straightened paper clip into it. This will trigger the release mechanism, which allows you to take off the handle. Look for a small tab that is located inside of the lock, and press it using a flat screwdriver. Once the spindle is removed, you can remove the cylinder and housing.

Making a decision on a new locking system

You have many options when it comes to selecting a new lock. Think about the various kinds of locks and choose one that is in keeping with the design of your door. Think about the backset (the distance between the door's edge and the center of the double glazing window lock replacement hole) and the cross bore (small hole along the edge of the door frame). Also, be sure to choose a lock that will be able to fit the door's thickness and swing.

The American National Standards Institute and BHMA have graded all door locks to give an idea of their durability and the difficulty to pick them or disable them. A grade 3 lock may be ideal for a peaceful apartment building in the countryside, whereas locks of grade 1 could be better suited to a busy street near the storefront.

Most smart door locks need a digital code to open. If you're worried about hacking or other security concerns seek out an expert locksmith or your local police department for assistance.

Replace the cylinder

If your door lock cylinder is damaged or broken you can repair window locks upvc it in a matter of minutes by completing a do-it-yourself project. The trick is to select the correct cylinder and follow the steps that accompany it. The first step is to take off the handle or knob should there be one, then unscrew the trim that is attached to the base of the lock cylinder using a screwdriver. Once the trim is removed, you can access the screws that hold the cylinder in place and remove them using the flat-head screwdriver. The cylinder is then gently lifted out of the door.

Before installing the new cylinder, you must make sure that it's the right length for the door you are using. Find the distance from the center to the left and right sides of the cylinder using the aid of a tape measure. Purchase a new cylinder which has the same measurements. This will stop cylinders from snapping when the door is hit or the key is stuck inside.

Once you have a suitable replacement cylinder, place it into the door and turn the key. This will align the cylinder with your carrier that is usually located on the outside of your lock. You can then loosen the set screws, which should be a couple of turns in the head. If there is a screw located on the edge of the case that holds the door, you will need to remove it.

After you have removed the lock cylinder and replacing it with the new lock by slipping the new cylinder into the case and tightening the set screw. It is also recommended to reinstall the part that connects the cylinder with the lock indicator stem, which you can do by removing three small tabs on back of the cylinder with needle-nose pliers. Attach the bracket that is smaller to the cylinder's back. Then, you need to reinstall the strike plate and latch plate, as well as the retaining ring that is attached to the top of the lock cylinder.

Installing a new lock

Begin by measuring the door's width if are replacing a lock that is already in use. Most locksets for residential use have a thickness of 3/8 inch to 1 3/4 inches. If your door is more thick it will require an extra-thick door kit that includes longer screws window and door lock repair longer tail pieces (for door knobs) or spindle extension (for deadbolts).

The majority of locks come with a detailed installation guide to assist you. Before you begin, go through the instructions to ensure that you have followed all the steps. The booklet will also provide you with an idea of the level of expertise required to complete the task. It is possible to ask a person who has worked with locks for assistance if are changing a lock the first time.

It's a good idea to cover the holes in the old hardware prior to installing the new lock. This will prevent the screws from falling through the holes, and also protect any tiles you have installed. It will also prevent any potential damage from rust, dirt, and grime. SECURAM Touch includes the masking strip or gaffer tape. However, you can use any tape you have.

After you have removed the screws that connect the interior portion of the lock section to the exterior side then pull it out straight away. It is important to do this quickly so that the lock doesn't end up accidentally closing on itself and damage the mechanism.

If the new window lock repairs comes with a latch bolt, fit the new bolt into its upper cross bore. Make sure you put it in the correct position, which is indicated by an arrow. Then, you can screw the latch plate onto the bolt.

Attach the deadbolt to the door jamb. Test the deadbolt by throwing it few times to verify that it is extended all the way to the strike plate and is fully secured. If you're using an electronic smart lock, make sure to follow the instructions to program it. This involves downloading an application, registering your e-mail address, verifying you identity and connecting to the wireless network in order to connect your device.