• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock change is an easy and inexpensive method to boost your home's security. This isn't for everyone. It requires a certain amount of skill and patience.

You must replace the cylinder that is located within the knob's body. The cylinder is what recognizes the key when it's inserted into the lock.

The old lock can be removed

The first step in replacing a door lock is to get rid of the old lock. It's a easy process, but you must keep a few things in mind. Make sure that the new lock is compatible with your door. This will ensure it is secure and doesn't create a gap around the latch or deadbolt.

After removing the latch plate, you will have to look for two bolts or screws on the inside of the casing which are holding the casing to the two halves of the lock. Remove them with a screwdriver and then take the lock out of the door. If you have a mortise locking system, there is a set screw that binds the handle to the spindle. Use a screwdriver to remove this screw, then pull out the doorknobs.

You must also remove the latch and deadbolt plug from the hole in the door jamb. Then, you can install your new upvc window lock repairs near me. If you're replacing a mortise, you should take a measurement of the distance between your lock case and the door edge to make sure that the new lock is a good fit.

It is possible to replace your lock for various reasons, for instance, if you suspect that someone else is holding the key or you have new roommates. In any event, you could save money by taking the lock off yourself rather than paying an expert to remove it. It's easier than most people think and can be completed in just a few minutes.

Begin by getting rid of the handle and trim from the door. With a flat screwdriver, take off the trim. You will be able to pull off the majority of it and in some cases the handles could come off completely. Next, search for a pinhole on the inside of the handle, and insert a straightened clip into it. This will activate the release mechanism and allow you to remove the handle from the door. Look for a small tab on the interior of the lock and press it using a flat screwdriver. After the spindle is removed, you can take off the cylinder and housing.

Making a choice for a new lock

When it comes time to pick the right lock for your home there are a lot of choices. Take a look at the various types of locks and choose one that matches the design of your door. Think about the backset which is the distance between the edge and the center of lock hole. Also, think about the cross bore, which is a small hole at the edge of your door frame. Also, be sure to choose a lock that will be able to fit the door's thickness and swing.

Most door locks are evaluated by BHMA and the American National Standards Institute to give you an idea of how they will withstand use and how difficult to pick or disable. A grade 3 lock may be the best choice for a peaceful suburban apartment complex, whereas a grade 1 lock might be more able to withstand the traffic that is frequented by a store front on a city street.

Most smart door locks require a digital code to open. If you are worried about hacking, or other security issues, talk to a professional locksmith.

Replace the cylinder

You can easily replace damaged or broken door lock cylinder with a simple DIY project. It is important to select the right cylinder and follow the instructions. The first step is to take off the handle or knob should there be one then loosen the trim around the base of the lock cylinder using a screwdriver. Once the trim has been removed, you can access the screws that keep the cylinder in place and remove them using a flathead screwdriver. The cylinder is then gently removed out of the window door repairs locks glass hinges.

Make sure you measure the length of your new cylinder prior to installing it. Find the distance from the center to the left and right sides of the cylinder with the aid of a tape measure. Then, purchase another cylinder that has the same measurements. This will stop cylinders from snapping when the door is kicked or the key gets stuck inside.

If you have a replacement cylinder, insert it in the door and turn the key. This will align the cylinder with the carrier which is located usually on the outside of your upvc window lock repairs. Then, loosen the set screws that should be only a couple of turns into the head. You will also need to loosen the screw in the door's edge which secures the case should there be one.

You can replace window lock the old lock cylinder with the new one by sliding it into the case, and then tightening the set screws. It is also recommended to reinstall the part that connects the cylinder with the stem for the double glazed window lock repairs near me indicator that you can do by removing three small tabs on the back of the cylinder using needle-nose pliers. Then, you'll be able to attach the smaller bracket to the back of the cylinder. Then, you should reinstall the strike plate and latch plate, as well as the retaining rings connected to the top of the lock the cylinder.

Installing the new lock

Start by measuring the width of your door if you are replacing an existing lock. Most locksets for residential use are designed to fit a door thickness of 1 3/8 - 3/4 inch. If your door is more thick, you will need a door kit that is thick and includes longer screws, longer tail pieces (for door knobs) or spindle extension (for deadbolts).

Most locks come with a detailed instruction manual to help you install the new hardware. Before beginning, you must read the instructions to ensure you have followed all the steps. The guide will also give you an idea of the degree of skill required to complete the task. If you're changing a lock for the first time, you may consider asking a more experienced person for help.

It's a great idea seal the openings of the old lock before installing the new lock. This will stop the screws from falling out of the holes and protect any tiles you might have installed in the area. This will also protect your tiles from damage caused by dirt, rust and grime. SECURAM Touch includes a strip of masking or gaffer tape, but you can use any tape you have.

Once you've removed the screws that hold the inside of the lock section to the outside side immediately, pull it back. It is important to do this quickly to avoid the lock from closing itself in a way that could end up damage the mechanism.

Fit the new latch bolt in the upper cross bore of the new lock, if it comes with one. Make sure that you place it in the correct position, which is marked by an arrow. Then, place the latch plate over the bolt and secure it in the correct position.

Screw the deadbolt into the jamb on the door. Test the deadbolt by throwing it few times to ensure that it extends all the way to the strike plate and is fully secured. Follow the steps included in your electronic smart lock to program it. This involves downloading an application and registering your e-mail address, verifying you identity, and connecting to the wireless network to add your device.