• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Sash Window Repair

Sash windows add a classy style to any home. Nevertheless, they can be drafty and difficult to clean due to age or wear. Sash window repairs can be a great option for enhancing functionality while maintaining the original appearance.

The first step in repairing sash windows is to remove "pocket covers". These are pieces of wood, tucked away on the frame, which allow access to the weights.

Sashes damaged by abrasions

If your sash windows are damaged or leaking air, you'll need to do more than repair the surface. You can save money by performing a more thorough repair, especially if your home is older and has low insulation. Here are some common problems with sash windows and how to repair them:

Stuck Issues

It can be difficult to shut or open the window in the event that the sash does not fit properly into the frame. This can result in rattling noises and allow drafts to enter your home.

To resolve this you can use a utility knife to cut the paint line on the inside side of the sash, then take it off. Be careful not to scratch the wood. After that, you'll need apply a sash grease that will make it move more easily.

Broken Sash Cords

Some old double-hung sashes have metal or cotton cords supporting the weights used lift and lower the sashes. As time passes, these cords can break, making it difficult to lift the sash and keep it up. To fix this issue, follow these steps:

Then, pull the sash to the right and take it off the frame. Pull the cord from the bottom of the sash. Cut it and take out any nails sticking out from the end. Pull the nail free with needle-nose pliers, then insert it back into the side channel. The knot of the cord should be tucked into the hole and secure it with a nail set.

Install the sash again and add the beads for staff. Be sure to leave slack in the cords for optimal operation. Install the counterweights and balances. To minimize draughts small amount of decorators caulk could be applied between the bead of the staff and the box.

When the frame and sash are repaired completely, cover them in glazing putty. Glazing putty is made with linseed and chalk. Mix in enough chalk to make it workable, and not stick to your hands. Allow the putty to dry completely before reinstalling sash or painting the frame.

Broken sash cords

Old double-hung (two sashes) windows are made of chains made of metal or cotton connected to counterweights that support and keep the sashes balanced in the window jamb. As time passes, the cords may break and prevent the sashes from opening or close. This makes it difficult to raise the window or lower it. Replacing the sash cords is an easy home fix that will solve these problems within less than a half hour.

Remove the staff bead that divides the upper and lower sashes. You can remove the bead using needle-nose pliers. Normally, a nail is inserted through the knot into the sash's casing to secure it. Remove any nail that is rusty from the stop beads and then clean the caulk as well as the old cord residue and paint around the groove of the sash.

To open the window, pull on one of the cords that run through the sash and lift it up. When you've made it as far as you can make a mark on the cord in pencil and cut it out using an utility knife. When you're done, be sure that the new cord is aligned with the groove on the sash secondary glazing. Also, tie it to the sash by knotting a knot.

If the sash remains too high to move, you can use your sharp side cutters to cut off and remove the old cords. Once the sash has been removed it is necessary to remove the access panel in the sash channel in order to expose the pockets of sash weights, counterweights, as well as the pulley system. If the window has been painted, you'll have to cut the seams using the hammer or chisel to remove the panel without damaging it.

Once you've removed your access panel, you can see the two cast-iron sash sash weights in each pocket. Remove the weights on the front and back and then tie the sash cords onto the weights with a self tightening knot. After tying the new cords, you'll need to reattach the sash weights and reset the pulley mechanism to ensure it functions properly.

Drafts

Sash windows add a touch of historical charm to older homes, however, they also pose issues with their maintenance. They can be difficult or even impossible to close and open with a smooth, quiet operation. They can also be rattled by winds, and letting drafts in. These problems are often caused by swollen wood, paint buildup or sash cords that have rotted. Fortunately, there are many inexpensive and cost-effective methods to repair the problem and keep your bespoke sash windows windows working properly.

The first step to repair an old sash window is disassembling it. Take off the sash and frame, and ensure that all components are in good condition. Then, sand the wood to enhance its appearance and to prevent drafts. A small amount of wax or silicone spray can aid in allowing the sash to slide more easily. If the sash remains stuck, use a knife to cut through any paint layers to release it. A new set of tilt-pins could improve the window's performance.

Weights are pushed across pulleys in order to counterbalance the weight of windows with sash. The weights are typically cast iron and are reached via an access panel or pocket cover within the lining of the box of the window frame. To prevent the weights from crashing down, an dividing strip is hung within the frame to ensure they don't collide.

Accessing these weights is difficult, since the upper sash is painted shut and is nailed into place. However, if you're patient and careful, you can remove the sash using bar clamps, reversed to disperse, to ease it out of its groove in the rails that meet. It may take a some tapping and jiggling to pull it out but once you've got it out, be sure to check the sash cord and replace it with new rope (not cotton) If you need to.

You can also change the balance of the sash to make it easier to open and close the window. It's not as difficult as you think to change the double-hung balance on a window. You can do it yourself if have the right tools and a replacement kit.

Rotten sill

Even the most well-maintained windows will eventually show signs of decay. If the rot is only affecting the sill of the window, it may be possible to restore it. If the rot has gotten into the frame and into the interior, and damaged structural components it could be time to replace the window.

It is important to replace a rotten window sill before it causes further damage to the window. The first step is to take off the sill plate that was previously installed and studs. If the studs are load bearing you may have to build temporary supports. After removing the old sill and cleaning any remaining paint from the sill plate. After the sill has been cleaned, replace it with a new board and nail it to the studs.

A stained sill is not just ugly but it could cause costly repairs in the near future. It could, for instance cause the sash, which is difficult to notice to see, to move. This can lead to a cracked, bowed or damaged glass pane. A sill that is rotten may allow water to enter the wall and cause mold.

It's not as difficult as it seems to repair a sill that is rotten. To avoid rot, keep the window clean and free of debris and dirt. Install a seal of protection on the window frames to keep them dry. Lastly, you should use a dehumidifier to regulate the moisture levels in your home. This can stop wooden sashes from expanding or sagging.

Sticking sashes are a common issue for windows with sash. You can fix this problem by applying a small amount wax or silicone to the window tracks. This will help them slide more easily. If the sashes are stuck due to paint buildup you can use an utility knife to cut the paint layers and release the sashes.

Reinstalling the parting beads is another option to fix a stuck sash. If the sash still sticks it is possible to try to draught proof it. This involves putting strips of rubber between the sash and frame, which reduces airflow and improves the acoustic quality of your window.