• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Repair Car Keys

The car keys are small and might not seem to be important, but they're essential for the operation of your vehicle. The cost of replacing a traditional or modern transponder car keys can range from $200 to upwards of $200.

There are many ways to repair your car keys yourself for less than the cost. This article will discuss the most common car keys problems and the DIY solutions to fix them.

Dead Key Fob Batteries

The remote key fobs that come with cars make it easier than ever to open the trunk, doors and tailgate. However, the battery inside the device could die. There are a few tricks you can use to resolve this issue quickly.

Examine if your vehicle is still in ignition mode. If it is, then the key fob battery may simply be depleted instead of dead. To test, press the fob's button against the ignition button on the vehicle. If this works, then the battery is likely fine and only needs to be changed.

To replace the battery in the fob, pry open the case with an screwdriver. Be careful not to apply too much force as this could cause the fob's casing to split. If the fob isn't opening try prying the tool several times around the outside of the case.

Open the electronic portion of your vehicle after you have removed the mechanical key. Install the new battery and then snap back the shell. If your key fob does not work after this procedure, it could be that there is a larger problem with the remote start system of your car key fob repair. This will require an expert to determine the cause. If this is the case, a trusted mechanic should be able to assist you. If you require assistance with your vehicle or vehicle, you can get roadside assistance.

Broken Key Ring

There are a few options to do in the event that your key fob won't work because the ring is broken. The first step is to see if the Broken key repair near me piece is still in the ignition. If it's still there the ignition, take it out without damaging the ignition lock or the door lock. Call a locksmith if you have difficulty taking the key off. They have tools that can safely remove a broken key from the ignition.

Another reason for a broken car key is the corrosion of the circuit board or plastic frame. You can clean the circuit board using a cotton swab and rubbing alcohol. This will get rid of the corrosion and protect to the contact pads.

Repair a damaged ring using a strong nail or wire to close the hole. Superglue can be used to fix the broken key ring. First, clean the damaged ring with a damp cloth and then apply a small amount superglue to the ends of the wire or nail. Let the pieces dry and then press them together. These DIY solutions may sound appealing, however they are only a temporary solution. For long-term repairs, you'll want to hire a professional locksmith. They have the knowledge and tools to fix the broken key quickly and effectively. They can even replace the battery inside your key fob and reprogram it if needed.

Broken Key Blade

Some key blades can break due to a lot of wear and tear. If this happens, it's time to buy a new key. The issue isn't as serious as you think at first glance. The primary issue is that the metal blade snapped off the case.

Spraying lubricant into the keyhole is one way to fix it. Then you can use pliers pins, or tweezers to grab the damaged key and take it out. You could also employ a magnet in the event that the key is magnetic. Just be careful not to use a magnet on an ignition key as it could cause the lock tumbler to break.

If you're not able to take the broken piece of key, contact a locksmith right away. They're equipped with special tools to safely remove keys without causing damage.

You can also try super glue to repair a snapped key. Apply a small amount to the edges and press them in. Wait until the glue dries before you insert your key into the lock. This method isn't reliable and you might have to repeat the process a few times before it works. Plus the super glue may not be enough strong to keep the key in place. This is more of a temporary measure than an option that can last.

Broken Plastic Loop

If your key fob key repair's plastic loop is damaged, it can make the key ineffective. Luckily, this is an simple fix. For a replacement alternative, you can use wire that is thick or a finishing nail. Drill two holes into the plastic loop that is broken for each end of the nail or wire. Cut the wire or nail into a key width, and place tiny drops of superglue into each hole. Then, press the wire or nail into the holes and let them dry.

Another option is to get a replacement shell from a locksmith who sells them. They can transfer the programmable section of your key to the new shell, and cut new blades for less than the cost.

This isn't the best option, but it can allow you to travel again if your key split in half. However, it can be difficult to repair the key blade if it is in the ignition. If you are not careful you could employ a hair clip, or needle to remove the broken part from the ignition. Contact a locksmith who has special tools to safely remove damaged keys from ignitions. They can also make you a new key with the appropriate cuts for the ignition of your vehicle and ensure it works perfectly when it is put into the lock.

Broken Master Key

If a mobile key fob repair is broken inside the lock, you'll have to find it before it gets completely destroyed. There are a few techniques you can employ, such as using lubricants, tools, needle nose pliers and tweezers. These tools can grab a fragment of the damaged key and then remove it.

Spray the inside of your lock with WD-40 or graphite powder. You can also use hacksaw blades by moving the blade across the face of a damaged key and then grasping a few of its 'teeth.' If you are successful then you should be in a position to take the broken key out.

Many hardware stores carry a spiral key extraction tool. This tool has a thin rod that is flexible and has spiral threads that can be inserted into the keyway, and then bent to form the broken part of the key. Once it has gotten caught on the serrations you can twist the bar in a circle and pull it against the broken section of the key.

Before contacting a locksmith try to remove the broken master key. If you are unable to get the piece out, you need to call the big guns - have a locksmith make you a brand new key and reprogram it to the transponder of your car.