• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock change is an easy and inexpensive method to boost your home's security. However, the procedure isn't for everyone. It requires a certain amount patience and expertise.

The cylinder is contained within the knob body. The cylinder recognizes the key when it is put into the lock.

The old lock can be removed

First, remove the lock you have been using for a while. This is a relatively easy process, but there are a few things to be aware of. First, ensure that your new lock is the right size for your door. This will ensure that it fits securely and does not leave a gap around the deadbolt plug or latch.

After you've removed the latch plate, look for two screws or bolts on the inside of the casing, which connect the casing and halves of the lock. Remove them with a screwdriver and then remove the lock from the door. If you have a mortise locking, there could be a set screw at the base of the handle that binds it to the spindle. Remove the doorknobs by unscrewing this screw with a screwdriver.

Remove the deadbolt as well as the latch plug from your door jamb. Then, you can install your new lock. If you are replacing a mortise lock you should also determine the distance between the lock case and the edge of your door to ensure that your new lock will be able to fit.

There are a variety of reasons that could prompt you to replace window locks your door lock, including being concerned that someone else may have the key or if you're welcoming a new roommate. You can save money by deciding to take the lock off yourself instead of paying an expert. The process is simpler than many people think and can be completed in just a few minutes.

Remove the trim and handle from your door. Then, pull the trim loose using a screwdriver that is flat. You will be able to pull off most of it, and in some instances, the handles might come off entirely. Next, look for a pinhole on the inside of the handle, and insert an unstraightened clip into it. This will activate the release mechanism, allowing you to remove the handle. Then, look for a small tab that is located inside of the lock, and press it with a screwdriver that is flat. Once the spindle has been removed, you are able to take off the cylinder and housing.

The choice of a new locking system

There are a lot of options available when it comes to choosing the right lock. Take a look at the various types of locks and select one that matches the design of your door. Think about the backset (the distance between the door's edge and the center of the hole in the lock) and the cross bore (small hole along the edge of the door frame). Choose a lock that fits the door's thickness and swing.

The American National Standards Institute and BHMA have graded all door locks to give an idea of their longevity and the difficulty to pick them up or disable them. A grade 3 lock may be perfect for a quiet apartment complex in the countryside, whereas a lock of grade 1 may be better suited to a busy street near a storefront.

Most smart door locks require a digital code to open. If you are worried about hacking or other security concerns, consult a professional locksmith.

Replacing the cylinder

If the cylinder of your door lock is damaged or broken, you can replace it in just a few minutes by completing a do-it-yourself project. It is essential to choose the appropriate cylinder and follow all instructions. First, take off the knob or handle if it is present. Then with a screwdriver remove the trim that is around the lock cylinder. After the trim is removed, you can take off the screws holding the cylinder in place using a flathead. The cylinder is then gently pulled from the door.

Before installing the new cylinder, be sure it's the right length for your door. Measure the distance from the center to the right and left sides of the cylinder using an instrument. Then, you can purchase another cylinder that has the same measurements. This will stop the cylinder from snapping, which can happen when the door is kicked out or when the key sticks inside.

Insert the replacement window lock cylinder in the door and then turn the key. This will ensure that the cylinder is aligned with the carrier, which is typically located on the outside of the lock. Then, loosen the set screws that should be only a couple of turns into the head. Also, you will need to loosen the screw at the door's edge that holds the case in place, should there be one.

After removing the lock cylinder after which you can replace it with the new lock by slipping the new cylinder into the case and tightening the set screw. Installing the part that connects the cylinder to an indicator stem for a lock is also important. You can do this by pulling three small tabs at the back of the cylindrical using needle-nosed pliers. Attach the smaller bracket to the cylinder's back. Then, you must put back in the strike plate and latch plate, as well as the retaining ring attached to the top lock cylinder.

Installing a new lock

Begin by measuring the width of your door if you are replacing an existing lock. The majority of residential locksets have a thickness of 1 3/8 inch to 1 3/4 inches. If your door is more thick it will require a door kit that is thick and includes longer screws and a longer tail piece (for door knobs) or spindle extensions (for deadbolts).

The majority of locks come with a comprehensive instruction booklet that will assist you in installing the new hardware. Be sure to read the instructions thoroughly before beginning the process to ensure that you've followed all the steps. The manual will also give you an idea of the level of skill required to accomplish the task. If you're changing double glazed window lock repairs glazing window lock repairs locks repairs (this site) for the first time, you may want to ask an experienced friend for assistance.

Before installing the new lock it is a good idea to cover the holes with tape the old hardware. This will stop screws from slipping through the holes, and also protect any tiles you might have installed. It also protects against possible damage caused by rust, dirt, and grime. SECURAM Touch includes a strip of masking or gaffer tape, but you can make use of any tape you have.

After you have removed the screws holding the interior half of the lock section to the outside side, pull it straight away. It is important to do this quickly to prevent the lock from accidentally closing and harming the mechanism.

If your new lock is equipped with an internal latch bolt, insert the new bolt into the upper cross bore. Make sure that you put it in the correct position that is usually marked by an illustration on the faceplate. Then, slide the latch plate over the bolt and screw it into the correct position.

Screw the deadbolt to the jamb of the door. Test the deadbolt by throwing it few times to verify that it extends all way to the strike plate and is fully secure. If you're using an electronic smart lock, be certain to follow the instructions to program it. This involves downloading an application and registering your email address, verifying you identity, and connecting to the wireless network in order to add your device.