• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Lock Door Locks

Your first protection is your door lock. It will prevent unauthorized entry to your home. The signs of wear and tear as well as instances like moving into a new home or break-ins, can necessitate the necessity of replacing your lock.

To begin, you must determine the size of your cylinder using the distance between the adjustment screw and the middle of the knob lock cylinder. This measurement will allow you to buy the lock that is right for you.

Deadbolt

Installing a deadbolt is excellent way to protect your door from intruders. The bolt extends into the strike plate that is on the door frame when it's locked, making it more difficult for burglars to break in through the door. A single-cylinder deadbolt can be activated using a key on the exterior, and the thumb-turn mechanism that is located inside. Deadbolts will only work when it is properly installed.

First, you must determine whether the door already has a hole that is suitable for a deadbolt or if you have to drill it out. Mark the location of the hole for the deadbolt on top of the door by using the template supplied with your lock installation set. Utilize your tape measure to determine the height of the deadbolt. Mark this height on the door edge. Use speedsquares to draw a straight line across the mark you made to mark the bolt hole.

Next, use a power drill to bore this hole until it reaches the other side of the door. This could take a bit of time. Sand the hole and edge of the door to make it smooth. It's also recommended to paint or stain the door at this point.

Once the door is ready, remove any screws visible on the deadbolt. This will reveal the rear and front assembly of the deadbolt as well as its bolt inside. Then unscrew the old bolt and replace patio door lock it by the new bolt to match the door hardware. The bolt is typically connected to a setplate which you'll need to unscrew. Once this is done then you need to chisel the area for the strike plate that is on the door frame.

If your strike plate is not in alignment It could be due to the previous installer didn't mortise it correctly or a weatherstripping has changed the strike's position. To correct this issue, you will need to remortise the strike plate and the deadbolt. Close and lock the deadbolt when you've completed this process. Make sure the bolt extends into the strike plate and then test the key to ensure it closes and opens smoothly.

Knob

It can make your home and business less secure when the door knob is worn. It could make it difficult to open or close the door, so it's recommended to replace it. It shouldn't take more than 30 minutes. Use a screwdriver or pliers to take off any knobs or handles. Be careful not to damage other parts of the door.

Spray WD-40 or another dry lubricant on the mechanism of your door knob prior to you begin. This will allow the new lock slide effortlessly as you turn it. It's essential to select the best knob and handle that matches your doors currently in order to ensure proper operation. If you don't have a doorknob that is compatible then you'll have to purchase a upvc replacement door locks.

Before you begin replacing the knob, take a look at the knob that was previously used to see what screws are keeping it in place. If there aren't any screws to hold it in place, you can use a screwdriver to secure the cover plate into the screws plate hidden behind it.

After you've removed your knob that was previously used, look it over for indications of damage or rust. You'll have to scrub it up if there are any scratches or marks, but you shouldn't have to do anything major when the knob is in good condition.

It's time to install the new one. It is important to first look over the two knobs to make sure that you've chosen the appropriate one for your door. You'll need to choose one that has an extending rod that's designed to lock into the second knob's rod mechanism. After you've placed the new knob in the hole, slide it into the latch.

Thread the latch plate screws down and test the spring by pressing down on it repeatedly. The latch should then spring back up every time. Then, put in the new knob and connect it with the rod mechanism on the first knob. Thread the long screws of the interior doorknob through the cylinder holes on the outside knob and secure it in its place.

Latch

A latch is a steel piece that extends out into the doorjamb in order to hold it shut. It is operated with a knob or handle on the inside of the door or a thumb turn on the outside side of the door. The latch can be secured with deadbolts to prevent thieves from breaking through the glass of the door. It can also protect against the accidental or deliberate closing by children or animals. A latch can be installed using one cylinder deadbolt or double glazed door lock replacement cylinder deadbolts based on the level of security you prefer.

Installing a deadbolt is the same as installing a latch, but there are some differences. First, measure the setback of the doorjamb using a tape measure to be sure the new lock will fit. The setback is measured from the edge of the doorjamb up to the center of hole for the latch plate. The standard setback is 2 3/8 to 2 3/4 inches. If you have a greater setback, you might need to purchase a more substantial latch at a hardware store or locksmith.

The next step is to drill an edge bore hole into the doorjamb for the latch plate. Use a chisel to chisel out the mortise for the latch and ensure it's deep enough for the faceplate of the new latch to sit in a flush position with the doorjamb. Place the strike plate in place to ensure that it's in the right position.

If the strike is positioned too high, the door could be pushed into or pressure put on it using a crowbar, or tire iron. This can cause cracks to the doorjamb. To fix this, the strike could be reduced by drilling a second hole through the doorjamb, and then chiseling out the core of the old hole.

The final step is to install the new strike plate, which can be accomplished by screwing it in place over the screw holes that are already in place. Then apply wood putty to cover the holes from the previous screws and the bolt hole that won't be used. Once the putty is dry then sand it to a smooth finish for an elegant finish.

Strike

An electric strike is a metal part where the deadbolt and latch engage when the door is shut. It is an essential part of the lock's security because it prevents the door from opening and gives an additional level of resistance to force or kicking. If a door is equipped with an electric strike, it can be opened with keys or the control unit that governs its electrical impulses.

Traditionally the installation of an electric strike meant cutting a small portion of the doorjamb to remotely release the latchbolt of a circular lock from the pocket within the strike. This modification is not just undesirable, but also exposes the mechanism of the latchbolt and the keeper to intruders.

Recently, several electric strike makers have come up with a brand new electric strike dubbed the "No Cut" strike that doesn't require a cutout in the doorjamb to function. These strikes have a unique design that allows the latchbolt and keeper to slide into the strike pocket without damaging the doorjamb faceplate.

The strike has an internal ramp that raises the latchbolt and keeper when it receives an electrical signal from a controller or reader. The retraction of the keeper and latchbolt causes them to rise on the ramp, which locks the door. When the door is closed, the deadbolt is retracted and the latchbolt retracts into the keeper.

Installing an electric strike can be an easy process, particularly if you are replacing an existing strike door. However, if you are upgrading to an electric strike for an access control system, you'll have to ensure that your new system is compatible with the kind of lock you've installed. You will also have to make sure that the strike is properly connected to your access-control system and set up to function in a safe manner.

Upgrade your strike plates to high duty strike plates to prevent unauthorised entry. These plates use four to six three-inch screws instead of the two three-fourth inch screws that are typically employed in regular strikes. These longer screws make it harder for people to break the frame and reach inside to turn the thumb turn part of a single deadbolt cylinder.