• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Handles

The door handles that you have in your home are an important part of the interior design. A new handle will bring your decor and space modern.

As time passes, your doors' knobs can start to feel stiff, or break. These are signs it's time to change the knobs. This guide will help you choose the appropriate replacement door handle repairs near me handle for your home.

front door handle repair Knobs

The handles on your doors can enhance the appearance of your house and make it easier for you to shut and open them. They are available in a range of finishes, colors, and types to complement your decor. If yours are starting to show signs of wear or you just want to upgrade, replacing them is relatively easy and can be accomplished in a few steps.

You must locate the shaft, or spindle, through which the knob is inserted to the door. Some have a small hole that you can put a narrow screwdriver into to remove the set screws holding the handle in place. Others have a thin slot or hole that you can use a flathead screwdriver to press on a spring-activated nut, known as a detent. When you press the pin, the latch mechanism releases and allows you to pull or push on the knob.

Once you have access to the shaft or spindle take the knob off of the door and replace it with the new one. Make sure you align it properly and verify that the latch works correctly before tightening the new set screws.

After replacing the knob, you can place the rod for the latch into the hole on the door. Lock it in place using the rod system on the second knob. Make sure the holes are aligned then thread the latch plate screws and tighten them.

Some homeowners opt for a brushed or smooth metal finish for the patio door handle repair near Me hardware to give their home a modern and sleek appearance. It will complement the furniture they have. Others prefer a more rustic style that is a good match for rustic-styled rooms. If you have someone in your family with mobility issues, you might want to choose an rim or lever lock, which requires less pressure to operate.

Other factors are being looked at more and more when it comes to the design of door handles. Accessibility and control of infections have been key issues in the creation of new handle designs. For example, some handle designs can be operated by an arm.

Latch

The latch that holds the door handle open can wear down as time passes. Switching out the old latch to make room for a new handle can be a simple DIY job and will make a significant difference in how your door opens and closes.

Depending on what kind of handle you choose the latch may be a separate part or an integral part of the knob. In either case, you'll need to follow the same process for removing and replacing. It's simple to take off the old latch, particularly when you have an entry handle that has a "magic" button. Located on the side of the knob, this little pressure-slot is what you have to press to take the latch right out of the handle and off of the latching mechanism.

If your handle doesn't have this magical button, the first step is to remove any cover plates that sit over the latch plate. They are typically circular or rectangular and can be removed using a screwdriver to pull them off of the handle. Some have a slot where you can place your screwdriver, whereas others just snap off.

Then, unscrew the machine screws that secure the plate's inner and latch to the door handle. These are the shorter screws with a pointy tip You will need to keep these in a secure location to use them again in the next steps. Once these are off you can pull the latch plate and mechanism out of the hole in the door and put it away.

Then you can begin to install the new latch. Install the inside plate of the latch into the hole in the door and secure it with the provided hardware. Make sure the square pin on the interior of the latch is facing the latching mechanism inside the handle and that it is lined up with the other screw chambers of the door handle. Then, push the exterior latch plate onto and secure it with the screws provided.

Strike Plate

It is not uncommon to replace a door handle if it is loose or doesn't lock properly. This is typically caused by incorrectly aligned parts of the latching mechanism, such as a striking plate that's either too small or has moved up or downward on the doorjamb with time. This easy project allows you to replace your old strike plate with a new, larger one that can provide greater security and will keep your door shut.

Apply a lipstick or other marking material on the bolt that you are using to determine if it's the strike plate. Close the front door handle repair and attempt to latch it. If the mark is below your strike plate hole, it means that the plate is too small and the door won't latch. If the mark is above or below the strikeplate hole the strikeplate is likely to have been moved upwards or downwards on the doorjamb.

Depending on your door depending on the door, you might be able to simply install the new strike plate into place over the old one with the screws included with it. But, you may have to drill holes first, and then chisel some of the wood to ensure it's a snug fit. If this is the case, be careful to not cut too much wood or you could damage the integrity of the doorjamb.

Installing a new box-style strike plate will provide the lock with a stronger hold on the doors and will require more force to open the doors. Typically it requires two long screws that anchor the strike plate to the door frame. You'll need to remove the old strike plate, then drill and chisel the wood to create space for the new one.

This hard-to-find strike plate is made to work with rim locks from the past, and it's constructed of robust solid brass with an extremely thick. This kit includes both wood screws as well as machine screws, allowing you to choose the right hardware for your requirements. Remember that wood screws have a pointed tip, whereas machine screws are blunter.