• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Kia Sportage Replacement Key

The key of many Kia models comes with the keyless entry feature built into. The key can be compared to an remote control, and can be replaced with a fresh one from an 2013 kia sportage key fob programming dealer or a locksmith.

Key fobs might stop working for several reasons, including the battery of the coin is dead, worn buttons or buttons, signal interference, water damage and a damaged receiver module. Here are some tips on how you can get your Kia Sportage replacement key working again.

How do you replace the remote key or smartkey?

The battery inside your Kia's smart key will eventually need be replaced, whether it is a remote key that starts with a push button or a regular key that does not contain a transponder. This is particularly in the event that your car displays a message telling that the smart key or remote has a low battery.

It's a fairly simple process. To replace the keyfob battery remove your mechanical key from the slit on the back of the fob. Then, you need to pry the cover open. A small screw is inside the key fob that holds the battery in place. By using a small screwdriver take the screw off and remove the old battery. Insert the new battery and close the gap on the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors unlock and lock according to your expectations, then you're all set! You can now take advantage of the hands-free lock/unlock feature on your kia picanto spare key when your fingers are cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a machine for programming, which is only available to the automotive locksmith or dealer. Other keys (non-transponder metal keys) do not require programming. If your keys need to be reprogrammed, you must be aware of the key code number written on the key code tag and record it in a safe place.

How to replace a battery

If the kia ceed key key fob is unable to respond when you press the lock/unlock button, it is most likely that the battery is depleted. A weak battery could cause other issues, like the check engine light flashing or the engine not cranking properly. It is relatively easy to replace key fob batteries with only the use of a few tools.

Before starting the process before beginning the process, ensure that your vehicle is off and that all doors are closed. Find the small metal or a plastic piece near the bottom of the key fob. Press it until the key is released. Then, you can insert the key in the handle of the door for the driver to unlock your car.

To replace the key fob's battery, take off the rear cover and use a plastic pry bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery, and then align the new one to ensure that the "+" positive side faces your face and the "-" negative side is facing towards the fob's metallic electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

After you have installed the new battery then turn the key fob off and on in the ignition until the door locks cycle. You can then test the kia car key programming (recent post by kingranks.com)'s key fob to ensure it's working as intended.

How can you replace the smart key

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key is equipped with an embedded mechanical key blade however, the standard key fob does not. Both types of key fobs have an internal battery that will eventually have to be replaced. Fortunately, it's a fairly simple process that takes only two minutes.

Make sure you turn off your Kia and be on a flat and well-lit surface prior to you begin. Be aware that there are tiny parts inside the fob that could fall out if not cautious.

The release button for the small size is located on the lower backside. It can be an oval silver button or a rectangular slot. When you press it the mechanical key blade will be released and you will be able to open the key fob.

After the key fob has been open, remove the battery that was in it. The new battery is a CR-2032 that can be bought online or from your local auto parts store. After you've finished it should be possible to lock, unlock and start your vehicle with your key fob even if the engine isn't running!

how to get a kia replacement key do I replace a mechanical key

The Kia keyfob is an excellent convenience that lets us lock or unlock our car with just pressing a button. Like any other device it is possible that the Kia key fob can occasionally have problems. Luckily, there are steps to take to fix these issues and keep our key fobs in good working order over the long haul.

A dead or low-quality battery is one of the most frequent problems. This could cause the fob to cease working or to work intermittently. If this happens, try replacing the battery with a fresh new one.

If this doesn't fix the problem then try using a normal flathead screwdriver to wedge open the fob's plastic casing. Be careful not to damage internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a brand new one.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob and check that it's functioning correctly. Contact a dealer locksmith to fix the issue in the event that the fob is not working. Make sure they make you an emergency key that functions in all the door and trunk cylinders to avoid future lockouts.