• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window pane Window Panes

A cracked window pane is an issue. It could also be an opportunity to upgrade your glass to energy efficient or insulated windows, and reap benefits like greater comfort, a higher resale value and reduced utility costs.

It's a task you can take on yourself for a fraction of the cost of hiring an expert. It requires the right tools and only an hour or two of your time.

Glass

If your single pane windows are old broken, deteriorating or damaged replacing them with more modern glass that is tempered or insulated can improve energy efficiency and reduce noise while maintaining the historical integrity of older homes. The procedure of replacing the window pane is simple and can be done by anyone with basic hand tools. You will also require a replacement window pane, glazier's suggestions, pliers, and latex glazing putty. If you need to, you can use a heatgun to warm the old putty. Before starting, put on gloves and safety glasses as working with broken glass could cause injuries.

Remove any broken glass pieces that remain. This is best accomplished with pliers, however, a flathead screwdriver may work in a pinch. Make use of a wood chisel or putty knife to get rid of any old putty that remains around the frame and the window sash. Work slowly and carefully and be careful not to damage the old window sash. This can be done best on an elevated ladder, not on the ground. Also, ensure that someone below the sash keep it in place.

Make sure the window frame is ready to accept the new pane when you have removed the old putty. Take measurements of the width and height of the opening in the sash by subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to an hardware store or home center, and have a piece of stock glass cut to size. You can also cut the glass yourself, if you have the right tools.

After installing the glass After installing the glass, apply some caulking around the edge. This will make the glass weatherproof. Install a glazier’s point on both sides of the frame. This will help secure the pane. The points should not be so tight as to cause friction between the frame and sash however they shouldn't be too loose.

Before putting the putty on, make sure to knead it until it is smooth and free of lumps. Roll it into pencil-sized strips. The first strip should be placed to the corner of the frame, moving from one corner to the other so that it is even and smooth.

Glazier's Points

The glazier's facets are small triangular pieces that help secure glass into frames for windows without scratching or damaging the fragile surface. Understanding how to use these hidden tiny helpers is simple and could save you money on professional installation or the cost of buying new glass.

After the old putty and glazier's points are removed, thoroughly clean the frame using a utility knife to eliminate any remaining traces. Lightly sand the frame in the rabbet grooves if needed to smooth out rough areas. If you decide to sand wood, protect it with painter’s tape to avoid accidental damage.

Measure the empty frame's dimensions and record precise measurements. Take these measurements to an hardware store or home center and have the new pane cut slightly smaller than the frame's opening. This will ensure a secure fit and leave room for expansion and contraction.

Insert the new pane into the frame and push it in with your hands. Then, use the tip of your chisel or the back of the putty knife to make a tap on the glazier's points, as illustrated in Figure 11. After you're done, the points should be flush with the top edge of the pane and the shoulders of the points should be below the lip of the rabbet groove.

Apply a thin bead of glazing compound over the edges of the new glass and in the rabbet grooves, to seal and protect them. Allow it to dry and cure completely.

Install the new window sash when the glazing compound has dried. First, saturate the wood with a heavy coat of Linseed oil. This will prevent the new putty drying out or cracking as it absorbs moisture. Use a brush to apply this coat, or the point of the blade. Then, use the chisel that is on the back of the tool or the back of the putty handle to gently hit the new sash, or glazier's point into rabbet grooves. Repeat this process in intervals of 10 inches around the frame.

Putty

A baseball thrown at you, an errant rock or a fallen branch can cause a window to crack or break. The majority of windows can be repaired easily by installing a new piece. The glass is held into the position with a tiny metal clip, called the glazier's point, and putty. This compound is also referred to as glazing compound. Remove the old pane and clean the area with an abrasive, pull-type scraper, or a wood chisel. Wear protective glasses and gloves when you work. If the window is glued to the frame, you'll need employ a heat gun in order to soften the adhesive prior to cutting it loose.

If you are planning to replace window glass near me the original sash, remove the molding pieces that hold the old pane in place. Sand the sash until it is flat and ready to receive new caulk. After the sash has been re-installed, apply a new caulk made of silicone around the glass to ensure it will not leak or change color in time.

Take the glazing points out of the rabbets, the grooves in the sash, where the glass is. If they're difficult to work out, try holding a hand tool like a heat gun over them to soften them first. If you're using a heated gun, be careful not to damage the railings of the sash or the sash itself by using the tool too closely.

Make the bed for your new pane after you have removed the old glaze and putty. Roll a rope made of glazing compound between your fingers and make it around 1/2 inch thick. Place it into the rabbets where the glass will be put. It's important that the glass is positioned against the putty on both sides So if you have to tap it, gently press the glass into the rabbet with your thumb.

If the new pane has damaged, you can use the silicone caulk or glass glue that is based on solvents to fill in the crack prior to pressing it into the sash. If not, you'll have to apply putty on the crack to create an airtight seal and keep water out. After the putty is dry and the film is oily, wipe it off the glass using a rag and allow it to dry completely prior to painting. Paint before the putty has completely dried. It won't form a good seal and may discolor or leak over time.

Paint

You may be concerned about replacing a damaged piece of glass. In reality, replacing a single piece of glass doesn't have to be expensive if you do it on your own. Even a double-paned window could be replaced for a fraction of what it will cost an expert.

First, if you are working on a large-sized window, replace window pane make sure it is securely attached to the frame. This task can be done relatively easy and quick with the proper tools and techniques.

If you're ready to begin with the removal of the old window pane by prying out the glazing points of metal that are connected to it. These are basically small metal triangles that function as "nails" that keep the window in within the frame of wood. They are buried under a bead of glazing putty that is then cured to form a solid, formed wedge that secures the window in place and conceals the points.

After removing the old pane, clean the frame and wood. Scrape off any paint and sand down the rabbet grooves where the glazing points were. These should be sanded down to bare wood, so that you can paint them the same shade as the rest of the frame. After sanding the wood then apply a layer of flax oil. This will help to extend its life.

Then, you need to measure the size of the window opening. You'll need to take horizontal and vertical measurements of the entire opening as well as the thickness of the old pane. To determine the exact size of the new pane subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass during seasonal changes. You can take these measurements to a hardware or home improvement shop and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.