• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

The first security measure is your door lock. It will stop unauthorized access to your home. Signs of wear and tear and also instances like moving into a new home or break-ins, can necessitate the necessity of replacing your lock.

To begin, you must determine the size of your cylinder using the distance between the adjustment screw and the center of the knob lock cylinder. This measurement will enable you to purchase the appropriate lock.

Deadbolt

Installing a deadbolt can be a ideal way to secure your door from intruders. When the bolt is extended into the strike plate of the doorframe it makes it more difficult for an intruder to get through the door. A single-cylinder deadbolt can be activated using a key on the outside and the thumb-turn mechanism located on the interior. A deadbolt will only work when it's properly installed, though.

It is first necessary to determine if the door has a hole that is suitable for a deadbolt, or if you have to drill it out. Mark the location of the hole for the deadbolt on the exterior of the door using the template included with your lock installation kit. Use a tape measure to determine the height of the deadbolt. Mark this high point on the door's edge, and then use the speedsquare to draw a straightline across the mark you made for the bolthole.

Then, use a drill to drill this area until the hole is on the other side of the door. This may take a while. Then, sand the hole and the edges of the door so that it's smooth. It's also a good idea to stain or paint the door at this point.

Remove any visible screws from the deadbolt. This will reveal the front and back assembly of the deadbolt, and also the bolt inside. Then, loosen the bolt and replace it with a new one that is compatible with the upvc door lock replacements hardware. You will need to unscrew the bolt from the setplate. Once this is done, you will need to chisel the area for the strike plate that is on the door frame.

If your strike plate is out of alignment It could be due to the previous installer failed to mortise it correctly or a weatherstripping has changed the strike's position. To fix this issue it is necessary to remortise the strike plate and the deadbolt. Once this is completed check the deadbolt by closing and locking it. Make sure the bolt extends into the strike plate and then test the key to ensure it is able to open and close smoothly.

Knob

It can make your home or business less secure if the door knob is worn. It may make it difficult to open or close the door, making it a good idea to replace door lock (click over here) the knob. Replacing the knob is an easy DIY task that should not take longer than 30 minutes to complete. Use a screwdriver or pliers to take off any knobs or handles. Be cautious not to scratch other parts of the door.

Spray WD-40, or another dry lubricant, onto the mechanism of your door knob prior to you begin. This will let the new lock slide effortlessly when you turn it. It is essential to choose the best knob and handle that is compatible with the doors you currently have to ensure that the lock is operating properly. If you don't have a matching knob, you'll need to buy an additional doorknob and latch plate.

Before you begin replacing the knob, look over the knob you replaced to determine what screws are that are holding it in place. If there aren't any screws, you can use the screwdriver to insert the cover plate into the screws plate that is hidden.

After you've removed the old knob, examine it for signs of damage or rust. It's important to clean it off if you notice any scratches or marks, but you shouldn't have to do anything major if the knob is in good condition.

Install the new knob. First, examine the two new knobs to ensure you're picking out the right one for your door. You'll need to choose one with an extended rod that is interlocked with the rod mechanism of the second knob. After you've placed the new knob in the door's hole, carefully slide it into the latch.

Test the spring by pressing down on it repeatedly. The latch should pop up every time. Install the second knob, and lock it to the rod mechanism of the first knob. Attach the other long screws from the interior knob through the hole in the cylinder of the doorknob on the outside and lock it in place.

Latch

A latch is a steel piece that extends out into the doorjamb to keep it shut. The latch can be operated by a handle or knob located inside the door, or by a thumb-turn on the exterior. A latch can be secured with deadbolts to prevent intruders from breaking in through the glass. It also protects against accidental or intentional closing of the door by children or pets. A latch can be installed using a single cylinder deadbolt or a double glazed door lock replacement cylinder deadbolt, according to the security level you prefer.

Installing a deadbolt can be the same as installing a latch but there are some differences. To make sure that the new lock is compatible, first measure the setback on the doorjamb with an instrument such as a tape measure. The setback is measured from the edge of the doorjamb up to the center of hole for the latch plate. Setbacks for standard latches are 2 3/8 to 2. 3/4 inches. If you have a greater setback, you may have to purchase a longer latch from a hardware shop or locksmith.

The next step is to drill an edge bore hole into the doorjamb to accommodate the latch plate. Use a chisel to chisel out the mortise for the latch, making sure it's deep enough to allow the faceplate of the new latch to sit flush with the doorjamb. Put the strike plate into place to make sure it is positioned correctly.

If the strike is placed too high, the upvc replacement door locks may be kicked in or pressure applied to it using a crowbar, or tire iron. This can cause the doorjamb to break. This can be corrected by drilling a new hole through the doorjamb and then removing the core from the old one.

The final step is to mount the new strike plate which is done by screwing it in place over the existing screw holes. Utilize wood putty to fill in any old screw holes or bolt holes that won't be used. After the putty has dried then sand it to a smooth finish for professional results.

Strike

An electric strike is the metallic part where the deadbolt and latch engage when the door is closed. It is an essential component of the lock's overall security, as it prevents the door from opening and provides an additional barrier to force or kick. If a door is fitted with an electronic strike, it can be opened only with an entry key and a control unit that regulates its electrical impulses.

In the past, putting in an electronic strike required cutting a portion of a doorjamb, which would let the latchbolt of a cylindrical lock from the pocket that is inside the strike. This modification is not only ugly, but also exposes the mechanism for the latchbolt and keeper to unauthorized users.

Recently, a number of electric strike manufacturers have come up with a "No Cut" type of strike that does not require a cutout for operation. These strikes have a unique design to allow the keeper and latchbolt to slide into the strike pocket without damaging the doorjamb faceplate.

The strike has an internal ramp that lifts the latchbolt as well as the keeper when it receives a signal from an individual reader. The keeper and latchbolt are lifted higher up the ramp due to retraction. When the door is closed the deadbolt remains at a lower position and the latchbolt retracts into the keeper.

Installing an electronic strike is a simple procedure, especially if you're replacing an existing strike. If you are upgrading an access control system to an electric strike, you must ensure that the new system is compatible. Also, you must ensure that the strike is properly connected to your access control system and is set up to function in a safe manner.

Upgrade your strike plates to heavy duty strike plates to stop unauthorised entry. These plates use four to six screws of three inches instead of the two three-fourth inch screws commonly used in standard strikes. These longer screws make it more difficult for someone to break the frame and reach inside to turn the thumb turn part of a single deadbolt cylinder.