• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat car keys 500 Key Fob Won't Work

A key fob from fiat panda key fob replacement 500 makes it simple to open doors and start your vehicle. There are a myriad of reasons the fob won't work. It could be due to a dead battery damage to the receiver module, water issues, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to search for local locksmiths in the automotive industry). This remote includes lock, unlock and fiat panda Key fob replacement trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob won't work is a dead battery. Modern key fobs come with a limited operating range, and should be within just a few feet of the vehicle in order to function. If you're far from your vehicle and press the keyfob button, it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the coin cell battery (Part number CR2032) with a fresh one from a trusted brand such as Panasonic, Duracell, or Energizer. You can find them at your local hardware store or online.

After you've changed the battery on the coin cell you can test it by standing near your fiat 124 spider key fob cover 500 and pressing the buttons. The car will flash its parking lights, and the key fob will operate the lock and unlock switches.

If your key fob doesn't work even after replacing the battery, there might be water damage that is preventing it from connecting to the module in your vehicle. Water damage can happen in a variety of ways, ranging from a light splash to submerging the fob in salt water at the beach. If you suspect that your fob has been exposed to water, you can place it in a rice bag to draw out the moisture. If this does not work, you'll need to have your fob reprogrammed either by an auto locksmith or a dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean or wash it in a machine. Saltwater poses a particular risk to the fob's circuit board and can cause it to short out and eventually end up dying. It's not a good idea to get the fob wet but don't give up even if you accidentally drop the fob in water or forget to take it out of your pants pocket.

First, remove the battery. Clean the electronic chip with isopropyl or a similar product and dry it thoroughly before replacing the battery. Then test the fob to see if it works. If the key isn't working it could need to be reprogrammed. This is usually done by an auto locksmith or dealer.

If the key is more recent and has not been programmed to your car It will most likely need to be replaced completely. A professional locksmith for cars will be able to complete this process. The locksmith will need to cut the key to match the ignition on your vehicle. They'll also have to reprogram the fob for your car's system. This is a quick and cost-effective process which can be completed the next day.

Receiver Module Issues

The 500 key fob you have may stop working because it is out of range. The remote typically has a range of 30 feet or less, and if it's too far away from your car it will not respond to your commands. This can be easily fixed by moving it closer to your vehicle until it begins responding.

If you've replaced the coin battery (commonly known as a "button" or "watch") and the fob won't work It could be because of an internal circuit board issue. In most cases, reprogramming the fob can resolve the problem. You can find the procedure for most vehicles on YouTube or in the owner's manual.

You may need to replace the metal clips that hold the coin battery. If they lose tension, it could prevent the battery from being properly seated and can cause the remote to malfunction.

In rare instances, the fob could be out of connection with your vehicle as a result of software or hardware problems. This can be a major problem, but you can often fix this by visiting a local dealer or auto locksmith to have them reprogram your fob. In certain instances, the software may also require reinstallation in your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit an signal. This could occur if the key fob is located near radio transmitters (cell phones and radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob may not function may be a lack of connection to the buttons or the internal chip or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. replacing batteries, reprogramming or using the spare key fob, you could have a defective receiver module on your 500. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's on-board system including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Reconnect the battery. This will eliminate any remaining electrical charge and restart the car's computer system, which could allow you to the key fob to function again. If the problem persists you should seek out a certified technician. They will be able to determine the root of any issues.