• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Replacement UPVC Door Handles

If you're replacing the handles or adding a little extra security you can choose the perfect handle for your door. These upvc handles are easy to install and meet the 92mm centers required by multipoint locks.

The most important measurements to consider are backplate fixing centres and lever/key hole dimensions. Make sure you compare these to your existing marks before ordering.

Lever/Pad

Lever pad handles are made up of a lever on one side and a handle that is shaped like a paddle on the other. They are designed to be used with key wind locks, however, they can also be adapted to multipoint split spindle door locks (though you'll need a separate dual spindle lock case).

Our range of upvc handle lever pads are available in a range of finishes. They will be shown in the drop down list once you have found the perfect handle for your door. Not all styles of handles are available in every finish and you should always look over the technical drawings and sizes sections for the particular product you're looking for to ensure that you are getting the correct size and fitting.

When choosing a new set of lever pad door handles made of upvc, it is crucial to make sure that they correspond to the PZ (distance between the handle spindle and the center of the hole in the cylinder) of your existing multipoint door locks, since they have to be in line for the doors to remain locked, either from the inside or outside. The handles we offer are designed to work with a variety of standard cylinder locks, but you should always double-check before ordering.

If you want to upgrade to dual spindle levers you'll need to take out the handles you have already installed and disassemble the lock case. This will require an additional split inline cylinder. These can be bought separately and we offer the complete technical diagram to examine in the images for each product.

It is recommended to loosen the screws that hold your existing door handle and then inspect the mechanism. If the screws are too tight it is possible to loosen them further. Then, you can remove the spindle from the handle and replace it with a new Upvc handle. Before putting the handle in position, it is recommended to ensure that it is in the proper place. You can do this by placing your finger in the space between the door frame and the door handle to make sure that it is level.

Lever/Lever

The lever handles for doors are used to operate a multi-point lock with a Euro cylinder. They are found on many upvc double doors as well as wooden and aluminum doors. They feature an inside lever and an outside paddle and are typically available in two varieties. Sprung - These include a spring cassette inside the backplate to help bring the handle lever to the horizontal position. Non-sprung: They do not have a mechanism for bringing the handle lever to a horizontal position.

To fix a door handle that is sagging you must locate the detent access hole or pin, which is typically a small rectangle or round shaped hole or protruding pin that is located on the opposite side of the base plate. Once you have located the hole for accessing the detent or pin, you can remove it with an screwdriver.

After the handle is positioned horizontally, you can install the screws. Tighten them to ensure that the window handle repairs stays fixed to the base plate. Consider applying a threadlocking solution to the threads of the screw to improve grip and prevent them from loosening over time.

There are a myriad of reasons why sliding door handles handles of levers drop. The most frequent reason is that the fixings have been over tightened and are putting strain on the lever bearing and causing it to pull against the door's face. It is also possible that the levers haven't been operated at the correct angle, which stretches the latch mechanism and stops it from fully springing into motion.

The most common reason for a spring lever not operating correctly is the spring not being in the correct position on the backplate. The simplest way to check this is to operate the handle to check if it returns to the horizontal position.

It is essential to fix any door handles that are damaged immediately. This could lead to excessive wear on the screws and the handle might fall off the base plate. It is also recommended to tighten loose screws frequently to prevent them from becoming looser.

Lever/Snib

These upvc handles are also called "Snib handle sets" and feature the snib lock button on the top of the lever. If you do not have a dummy locking device you can use this feature to lock the door. These handles are fitted with the Fullex lock 68PZ. (68mm between spindle and the centre of the lock). We also stock a range of 68PZ door handle from manufacturers like Ferco and Fab & Fix.

Change your door handle is a cheap method to upgrade your home, regardless of whether you're replacing handles that are in use or fitting new ones on doors that you've constructed in your home. There are a variety of styles of door handles made of upvc with traditional levers on backplate, straight or curving short latch and knob handles with dummy handles for multi-point locks, which are perfect for French doors.

Lever on backplate handles are often rectangular in shape but there are also circular or oval shaped versions that are referred to as rose door handles. These handles are identified by a lever or knob that is attached to a backplate. The backplate can be removed to allow for hidden fixing.

There's a wide selection of chrome and colored finishes available for these handles to enhance your door and hardware, including hinges, knobs and bolts. Some handles have a an grub screw that can be used to connect the knob or lever securely to the spindle. Some handles come with bathroom spindles, which can be used to make bathroom locks. They also come with a thumbturn release mechanism, and can be used on doors for bathrooms.

Mortise

The tubular latch is most likely to be the cause in the event that your door handle is slammed shut. There may be a few things that can cause this, the first being a simple lack of lubrication on the latch plate. It is possible to fix this problem by opening the door and spraying lubricant onto the handle and lock. It could also be that the latch is loose from the backplate. This can be a bit more complicated and will require a specialist to repair.

A multipoint door handle is a great solution to the problem of a door handle that is stuck. These handles are mounted through the faceplate and operated with a key or thumb turn knob which activates the cam that locks the deadbolt. The handles are available in a variety of sizes that will fit various kinds of uPVC doors. They are also available in an array of attractive finishes to complement the existing hardware. These handles are available on the internet or through an authorized locksmith in your area. They are simple to install and come with clear instructions.

To choose a replacement handle set, you'll have to determine the PZ dimension of your cylinder. This is the distance from the edge of the frame of the door to the center edge of the hole in the handle in millimetres. You will also need to be aware of whether your door has hook locks or a mortise lock. Once you have these measurements, the simplest method to determine the right handles is to filter by brand on the website. This will help you narrow down your options, and then you can choose the appropriate size.

A typical handle set comprises a handle unit with two screws of various lengths, drill guides and instructions for installation. Smart versions, like the Igloohome Smart Mortise 2+ include a mortice lock with keypad. These are more complex models that are best for professionals or highly skilled DIYers. Some handle sets come with many accessories, like weather strips, which can be used to enhance the appearance of the door.