• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are easy to maintain and durable, as well as long-lasting. In contrast to aluminium and timber, they don't get rusty or decay.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will prevent unnecessary repair costs as well as improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and even be fatal. It is crucial to take the time to make sure that you are doing everything you can to keep your windows in good condition.

Single-pane windows are relatively simple to replace and typically fit into frames that were previously in use very easily. However when you have double pane windows that are secured by internal beading, it will be more difficult to remove the existing panes and install new ones. In this situation it is essential to buy plastic spacers to aid in fitting the new pane into the window frame.

If you're planning to attempt to remove the window panes by yourself, it is essential to wear the appropriate safety equipment that includes gloves with a thick layer of material and eye protection. It is also recommended to lay down a dropcloth before you start working on the glass, so that any shards fall onto the cloth instead of onto the floor where they can be trampled on and cause further damage.

It's a great idea seal the gap after the glass has been removed. This will prevent drafts and water from entering your property until a professional comes out to repair the window. It also acts as an obstruction to prevent intruders from getting into your home. If the gap between the door and the window replacement is large, you might want to use an alarm system that includes a window. This will give you the best of both.

2. Sagging

uPVC is durable, energy-efficient and affordable alternative to timber sash windows. However, with time, they can suffer from a variety of issues, Window doctor including sliding. A sagging uPVC windows could cause issues with light, draughts, and even security. If you find that your uPVC window is beginning to sag it is important to act swiftly to stop the issue from getting worse.

Repositioning the hinges could aid in fixing a window which is sliding. First, you'll need to unblock the windows so you can reach the frame. With an screwdriver, take off the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Once you've repositioned the hinges, close the window and test it for fit. If you're satisfied with the fit, you can tighten the screws until they stay in place.

If you can't reposition the hinges you may need to replace the seal. As time passes, rubber seals lose their elasticity and become dry, which causes their tightness to decrease. It is crucial to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

uPVC handles could also loosen. Often this is due to screws that have become loose over time. However, it could be due to the fact that the handle mechanism has worn out. It's fairly simple to repair a loose uPVC handle. You'll first need to close the window and then perform an experiment fitting. The joint at the corner of the sash should align with the joint on the casing. If it isn't, you can use the screwdriver to loosen the handle. Then, turn the mechanism back into place.

3. Water Leaks

If you awake to damp floors and mouldy walls each time it rains it is important that you take action. Water leaks through windows can cause structural damage to your home and also hinder your ability to control the temperature in your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

It is a fairly easy fix that can be done by any DIY expert. Depending on the severity of the problem is, the old caulking might need to be removed. It is essential to keep in mind that when it is about uPVC window repairs you should avoid the temptation to "over-caulk' as this will only make the area harder to clean and can reduce your energy efficiency.

Make sure that the drainage holes have no debris in them, and also that the sill pan is angled correctly to drain away from the window. In more serious cases, you may need to replace the window.

Moldy sills and rotten ones are also signs of water leakage. The mold thrives in damp environments and can quickly spread across the house.

It is also important to remember that if the leak originates from the glass in your double glazing glazed windows, it's more likely to be a problem with the glass seal, rather than the frame or sagging. A uPVC specialist can easily fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and blow open in a breeze It could be hinges at fault. Any competent DIYer can replace the hinges in a matter of minutes.

Like all mechanical parts hinges are prone to wear out over time. It is very easy to change the hinges on a window however it is simpler if you have someone to help you to hold the frame.

Verify that the uPVC hinges are closed and open in the proper direction. Look for the arrows on each hinge to determine the direction in which the Window Doctor should be opened.

Faulty window hinges can be caused by incorrectly opening the window in a particular manner or because of poor installation at the factory. This can often be resolved by sending us a photo via our website and we will be pleased to offer you advice.

Regularly lubricating the hinges is also necessary. Applying a light engineering lubricant to the hinges is a good method to accomplish this. We recommend using an oil that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window operate and close more smoothly. It can also prevent corrosion and reduce the risk of sticking. Ideally, you should perform this every year. WD40 or other solvent-based oils should not be used since they can damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different things. The hinges can also be misaligned due to wear, causing an opening where the sash meets frame. These can be easily repaired by giving them thorough clean, however when they're beyond repair, it might be necessary to have them realigned or replaced. The interlock may be unbalanced. It is located on the hinge's side, and might require to be cleaned. In certain instances it might be necessary to replace the hinges.

The second most frequent reason for draughts are the window seals, these are prone to wear or damaged over time and let air escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity glasses. This will help to regulate indoor temperatures and decrease draughts.

Another, and most effective methods to reduce draughts is by using a draught excluder, these are typically made of fabric that are filled with some type of filler. They can be placed on the windowsill on top. These will keep your home warm by blocking cold air.

With a bit of regular maintenance and repairs, your upvc windows will provide an excellent level of security and insulation for your home. However, it is important to recognise that all windows have a lifespan and eventually, they will reach an point at which it is more economical to replace them than repair them. If you are experiencing issues with your window made of upvc you should consult an expert as soon as you can.