• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace Window pane Window Panes

A damaged window pane could be a source of frustration. It could be a chance to upgrade your windows to energy efficient or insulated ones and enjoy benefits such as improved comfort, increased resale values and reduced utility bills.

You can do it yourself for only a fraction of the cost it would cost to hire an expert. It requires the right tools and only an hour or two of your time.

Glass

If your single pane windows are old damaged, cracked or deteriorating replacing them with more modern glass that is tempered or insulated can increase energy efficiency and decrease noise while maintaining the original character of older homes. The process of replacing windows is easy and can be completed by most homeowners who possess basic hand tools. In addition to a replacement pane, the following components are needed such as latex glazing putty; Glazier's points; pliers and a heat gun for warming the old putty if required. Wear safety goggles and gloves prior to beginning. Working with broken glass could cause serious injuries.

Take away any broken glass pieces that remain. It is recommended to use pliers however a flathead could be used as well. After that, use a wood chisel, or putty knife, to take the remainder of the old putty from around the frame and the sash. Be careful and slow, taking care not to break the existing window sash. This can be done best on a ladder, replace window pane not the ground. Also, you should have someone lower to keep it in place.

Once you have removed all of the old putty, you can prepare the window frame to accommodate the new pane. Measure the width and height of the opening for the sash by subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to the nearest hardware store or home center and get a piece of stock glass cut to size. You can cut the glass yourself if you have the right tools.

After putting the new pane in place After installing the new pane, apply a small amount of caulking along the edge to ensure it is weatherproof. Then install a glazier's point on each side of the frame to secure the pane into the right place. The points shouldn't be too tight that they create friction between the frame and sash However, they should not be loose.

Before putting the putty on, work it in a gentle manner until it is smooth and free of lumps. Make it into pencil-sized strips. Place the first strip in the corner of the frame, working from one corner to the other to ensure it is smooth and even.

Glazier's Points

The glazier's points are tiny triangular pieces of steel that allow glass to be secured into the window pane replacement frame without causing any damage to the fragile surface. It's simple to learn how to use this secret tool and you can save money on the expense of a professional installation.

After getting rid of the old putty glazier points as well as any remaining remnants, clean the frame thoroughly with an utility knife. Lightly sand the wood in the rabbet grooves, if necessary, to smooth out rough areas. If you do sand the wood, ensure you protect it by using painter's tape to prevent accidental damage.

Note down the dimensions of the frame. These dimensions can be taken to the hardware or home center store, and the new frame will be cut to a smaller size. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new pane in the frame and press it into place firmly using your hand. Utilize the point of the chisel or the edge of the putty blade to smudge the glaziers' points as shown in Figure 11. When you're done taping, they should be level with the top edge of the pane. the shoulders of the points should be below the rabbet's lip. groove.

Apply a thin bead of glazing compound on the edges of the new glass and into the rabbet grooves, to seal and protect them. Allow it to dry and cure fully.

Once the glazing compound has dried and replace window pane the glazing compound is dry, you can install the new window sash. The first step is to coat the wood with an even layer of linseed. This will prevent the newly-created putty drying out or cracking as it absorbs moisture. Apply the coat using a brush or the tip of your putty knife, then use the chisel or the back end of the knife to gently hammer the new sash and glazier's point into the rabbet grooves. Repeat this procedure every 10 inches around the perimeter of the frame.

Putty

A hurled baseball or a rock that is errant or a falling branch can cause a window to crack or break. Most windows can be replaced by simply putting in a fresh piece. The glass is held in position by a small metal clip, called the glazier's point, and putty. This compound is also called glazing compound. Remove the old pane and clean the area using the rag, a pull-type scraper, or a wood chisel. Wear gloves and safety glasses while doing this work. You'll require a heat gun in the event that the window is glued to the frame.

If you are planning to install your original sash, you must remove the mold that holds the old pane. Sand the sash until it's flat and ready to receive new caulk. After the sash has been installed, you can apply a silicone caulk to the glass. This will ensure that it won't get soiled or discolor over time.

Remove the glazing points in the rabbets. These are the grooves on the sash, where the glass is located. If they're hard to chisel out, try holding an instrument like a heat gun over them to soften them before you do. If you're using a heating gun, be careful not to scratch the sash or its railings by holding the tool too closely.

After the old glazing points and putty have been removed make a bed for the new pane. Roll a piece of glazing compound between your hands, and form it to be about 1/2-inch thick. Place it into the rabbets, where the glass will be placed. It is essential that the glass sits on the putty in all places on both sides, so if you need to tap it, gently press the glass into the rabbet with your thumb.

If the new pane has a crack, you can cover it with a solvent-based glue or silicone caulk prior pressing it into the sash. In other cases, you'll need to putty over the crack to form an airtight seal and keep water out. After the putty has dried remove the oily film off the glass and let it dry completely before you paint. If you paint before the putty has completely dry, it won't form an effective seal and could discolor or leak over time.

Paint

You may be concerned about replacing a broken pane of glass. The truth is, replacing a single pane of glass doesn't need to be expensive even if you do it your own. Even double-paned windows can be replaced at a fraction of the cost it will cost for a professional.

If you're working with a large glass window first ensure it is securely attached to the frame. This job can be done relatively easy and fast with the proper tools and techniques.

When you are ready to begin, remove the old window pane. Remove the glazing points made of metal that are attached to it. They are basically tiny metal triangles that function as "nails" that hold the window in place within the frame of wood. They are buried beneath a layer of glazing putty, which is then cured to form a solid, moulded wedge which holds the window in place and conceals the window's points.

After you have removed the old pane taken away Clean up the frame and wood. Scrape off any paint that has been used, and sand the rabbet grooves where the glazing points were placed. Sand them down to clean wooden surfaces so you can paint the frames with the same shade. After sanding, apply a coat of flax oil on the bare wood to extend the life of the frame.

Next, measure the size of the window opening. You will need to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. To determine the exact dimensions of the new pane subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. Take these dimensions to your local hardware or home improvement store and have cut the glass for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.