• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen work from high off the ground, maneuvering massive glass panes. They follow strict safety protocols and frequently work in harsh weather conditions.

Wearing protective clothing, take off the metal glazing points as well as all glazing putty with an utility knife. A heat gun can to soften and take off the old putty.

Replacement

When a window's pane breaks, it can be tempting to try and repair the glass rather than replace it. However, replacing a window repair is typically more cost-effective and may aid in preventing other issues that could affect your home's energy efficiency. It is also important to consider the type of glass that is broken to determine if this is temporary or if you will require a more permanent solution.

To fix a broken window, you must remove the frame or sash and place it on the work surface. While wearing eye protection, carefully wiggle and pull out any shards that remain in the window pane. Use a utility blade to cut off the glazing compound, and the glazing points that secure the window. Keep an eye on the components and where they are to ensure they are reinstalled.

Once the frame and sash have been removed and the frame is removed, you can begin preparation to install the new glass. Before you begin make sure that the opening in the frame is properly sized for your replacement window. To allow for expansion and contraction of the glass and frame and contraction to both directions, measure the opening and subtract 1/8 inch. Afterwards, purchase double-strength glass cut to these exact measurements. It is a good idea to purchase enough glazier's clips or points to be installed every 6 inches around the window pane.

If the manufacturer is responsible you should contact them and make an claim. After the new glass has been installed, it needs to be sprayed with a thin coating of the compound used by glaziers. After letting the compound dry, you can paint it to match the frame of the window.

If you have a crack that extends more than an inch, cutting an arc of the edge of a blade just over the crack will help stop it from spreading further. This technique isn't 100% foolproof, but it can slow the growth of the crack down to a manageable amount until you can take more permanent measures.

Repair

Professional window contractors are equipped with the appropriate tools and know how to work with different kinds of glass. They also understand the best methods for disposing of waste, so they're less likely to leave crumbs in the trash, which could cause harm to pets or family members. They're also accustomed to working with various types of windows, and they may be aware of issues that aren't obvious to the uninitiated homeowner.

Before you begin the process of repairing cracked window glass, ensure that you wear safety goggles and gloves. A minor crack could cause shards of glass to fly away, creating a risk for anyone living in or around the home. It is also crucial to determine the cause of the crack in the first place, as it can help prevent future issues.

Begin by creating a two-part epoxy mixture. They are typically 50/50 mix of hardener and resin, and they must be mixed quickly. Once the mixture has been prepared then apply it directly to the crack and let it dry. It will take just a couple of minutes, but it is important to work quickly because the mixture is extremely thick and will dry very quickly.

Once the epoxy has dried, you can take off excess epoxy with a blade. Then, you'll need to clean the area around the cracked glass. If you don't do it correctly, the residue could cause further damage to the glass. Use a putty blade to smooth the compound around the edge of your window and then match it to the wood frame.

For a more durable solution you can consider using a plastic covering. A heavy-duty trash bag or tarp is the best option, but you can also apply masking tape to the glass. This will keep the crack from expanding and will also keep out wind, water, bugs, and debris.

You can create an interim fix if you are unable to access the window in a timely manner. Simply place a tiny amount of the substance around the outside of the broken window. It won't seal the gap between the frame and the glass completely however it will keep the broken piece in place until you are able to repair it.

Repainting

If your windows with glass are old, you may need to paint them. This is a cost-effective alternative to replacing windows, and can give your home a new appearance. Make sure that the surface is clean before painting. Wash the window with water and soap or ruby alcohol to eliminate oil smudges and other residues that could hinder the paint from adhering. Wear rubber gloves when working on glass surfaces to avoid the transfer of oils from your hands onto the glass. Finally it is recommended to apply several thin coats of paint instead of a single thick layer. This will help the paint last longer and will keep your windows looking even and smooth.

Make sure you have the right tools in your arsenal if you plan to repaint glass windows. You'll require a brush or sponge, painter's adhesive, a ruler, toothpicks, and other tools such as paper towels or a rag. You should also have the brushes and paint you'll be using for the project on hand. Follow the instructions of the manufacturer. Have patience because it could take a while for the paint to completely dry.

It is also important to ensure that the space you're working is ventilated when you're using solvent-based paint. This will reduce the risk of breathing toxic chemicals, and also the paint will dry faster. You should also make sure you have a protective mask for any spray paints you use.

For older glass windows, you'll need to prepare the surface prior to painting. Make use of soap and warm water to thoroughly clean the glass window. Then, use rubbing alcohol on any oil or Window Repair grease remnants that may hinder the adhesion of the paint. Make sure the windows are dry before you begin coating them.

If your glass windows are energy-efficient dual pane windows, you may be able to file a claim with the dealer or window company that sold them to pay any repair or replacement costs. This is especially true if the windows are still under warranty and you've had numerous issues with condensation or broken glass.

Sealing

If you have double-pane windows with broken seal or a newer version of insulated glass units (IGUs) that have experienced fogging or fog, there are many options to address the issue. It is the most expensive option to replace the IGU that is insulated as well as the frame. However, it may be required in situations where fog or condensation is causing energy loss. Other options include replacing the IGU by a single pane, or fixing the IGU that is in place by drilling a hole through the bottom and filling it with an anti-fogging solution.

You can also seal up the gap between a window frame and a threshold or sill by using a felt strip or vinyl V-strip. Felt can be stapled, glued or put in place, but it is not a great protection against moisture. Vinyl weather stripping that is v-strip is strong and easy to put in however it is costly and is typically reserved for areas that are exposed to high abrasion. Door sweeps can be easily nailed in place and are cheap. However, they provide very little or no protection between the threshold and air.

To fix a damaged window seal using a putty knife, you need to take off the caulk. Wearing gloves and eye protection remove the glazing point -- small fasteners with sharp pointed tips that hold the glass in the recess of the frame. After removing the glazing points, clean out the grooves and sand down the wood. Clean any sanding dust and then seal the unfinished wooden surface with a linseed-oil-based paint or clear sealer.

Traditional glazing putty can be applied using the help of a putty blade or caulking gun. However, a knife provides a better precision and precise application. It also creates a better seal. Choose a putty that is specifically designed for glass windows, as it will be more adhesive and durability.

Apply a small amount the putty to the inside edge of the frame where it touches the glass. Slide the window into the frame so that the drawn line on the glass aligns with the edge of the frame. Apply pressure to the glass to force the putty to form a tight seal. Smooth the compound using a gloved hand and remove any caulk or drips that were not properly applied before it dries.