• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen can maneuver large glass panes from a high point above the ground. They adhere to strict safety standards and frequently work in harsh weather conditions.

Wearing protective clothing, remove the metal glazing points and the glazing putty by using a utility knife. A heat gun can help to soften the old putty and accelerate the removal process.

Replacement

When a window's pane breaks, it can be tempting to try and repair the glass instead of replace it. However, replacing windows is typically more cost-effective and may assist in preventing other issues with your home's energy efficiency. Take a look at the kind of glass damaged to determine whether it's a temporary fix, or if a more permanent solution is needed.

The first step in repairing a broken window is to remove the sash, also known as the frame, and lay it flat on a table. Wearing eye protection, gently move the frame and remove any shards remaining in the window. Then, use a utility knife to remove the glazing compound as well as the glazing points that keep the glass in the position. Keep the track of the components and their location so they can be reinstalled.

After removing the frame and sash you can begin preparing to replace the glass. Before doing this, make sure that the opening in the frame is size for the replacement window. To allow for frame and glass expansion and contraction, measure both directions across the opening and subtract 1/8 inch. Then, buy double-strength glass cut to these precise dimensions. It is also an excellent idea to buy enough new glazier's points or clips to be placed every 6 inches around the window pane.

Depending on the warranty of the window it could be covered by the manufacturer in which case you need to contact the company to file a claim. Once the new glass has been installed, it needs to be covered with a thin coating of glazier's compound. After the compound has dried and dry, you can paint it to match the frame of the window.

If the crack is greater than an inch, you can prevent it from spreading by cutting a small arc just beyond the crack. This method isn't foolproof, but it can slow the growth of the cracked until you can take permanent measures.

Repair

Professional window repair installers are equipped with the appropriate tools and know how to handle different kinds of glass. They also know the best methods for disposing of waste, window Repair so they're less likely to leave scraps in the trash, which could hurt pets or family members. They are also experienced in working with different types of windows, and may be able to spot problems that an inexperienced home owner would not notice.

Wear safety glasses and gloves prior to beginning the process of repairing damaged glass. A small crack could cause glass shards to fly and put anyone at risk inside or around the house. It is also crucial to determine the cause of the crack in the first place, as it can help prevent future issues.

Make a two-part mix of epoxy. They are usually a 50/50 mixture of resin and hardener and must be mixed quickly. After the mix has been made and applied, simply apply it to the crack and allow it to dry. This should only take about a minute but it's important to do it quickly because the mixture is very dense and fast drying.

Once the epoxy is dried, you can get rid of any excess with a putty knife. After that, you'll need clean the area around the broken glass. If you don't clean the area in a proper manner, the leftovers could cause further damage to your glass. Once the glass is cleaned using a putty knife, you can use it to smooth the compound along the edges of the window, and then match it with the wood frame.

Think about using a plastic lid for a more robust option. You can cover the glass with masking tape or a heavy-duty trashbag. This will prevent the crack from expanding and will also keep out water, wind insects, water, and other debris.

You can make an interim fix when you are unable get to the window in time. Simply apply a small amount of the substance around the outside edge of the broken pane. It won't completely fill the gap between glass and frame however it will keep the break in place while you repair it.

Repainting

Repainting your old glass windows is a great idea. This is an affordable alternative to replacing windows, and it can give your home a new look. Make sure the window is clean before painting. Clean the window using soap and water or use ruby alcohol to eliminate oil smudges and other traces that could hinder the paint from adhering. You should also wear rubber gloves when working on glass to avoid the risk of transferring your own oils onto the window's surface. Apply several thin coats instead of just one large coat. This will help the paint last longer, and ensure that your windows appear even and smooth.

If you're planning to repaint your glass windows, ensure that you have all the right tools nearby. You'll need a sponge or brush as well as a painter's tamper along with a ruler, toothpicks and a ruler. You should also have the brushes and paint you'll be using to complete the project. Be sure to adhere to the manufacturer's guidelines and have a good amount of patience as it can take some time for the paint to dry.

If you are using solvent-based paints, you must make sure that the area where you work is adequately ventilated. This will reduce the risk of breathing toxic chemicals, and also the paint will dry faster. Wear a mask to protect yourself when using spray paints.

For older glass windows, it is necessary to prepare the surface before painting. Clean the glass thoroughly with soap and warm water. Then, use rubbing alcohol to scrub off any grease or oil that could hinder paint's adhesion. Make sure the windows are completely dry prior to coating them.

If your glass windows are energy-efficient dual pane windows, then you might be able to make a claim with the window company or dealer that sold them to pay any repair or replacement costs. This is especially true if your windows are still under warranty and have experienced several problems with condensation or broken glass.

Sealing

If you have double-pane windows that have a cracked seal or newer insulated glass units (IGUs) that have experienced defogging and fogging, there are a variety of options to fix the issue. It is the most expensive option to replace the insulation unit and the frame. However, it may be necessary if fog or condensation is causing energy losses. Other alternatives include replacing the current IGU with a single-pane, or fixing it by drilling a small hole in the bottom of the unit and filling the solution with anti-fog.

You can also seal the gap between the window frame and the threshold or sill with a felt strip, vinyl v-strips, or a door sweep. Felt can be stapled, glued, or nailed into place but is not a great protection against moisture. Vinyl v-strips are simple to put up and is durable, but can be expensive. It is usually reserved for areas that are subjected to high abrasion. Door sweeps are inexpensive and can be fixed to the floor, but they create very little or no protection between the threshold or sill and air, dust, and debris.

To repair a damaged window seal, use a putty blade to take off the caulk. Wearing gloves and eye protection, carefully pry out the glazing points -- tiny fasteners that fix the glass in the frame's recess, with sharp and pointed edges. After removing the glazing points, clean the grooves and sand the wood to a smooth finish. Wipe away any sanding residue, then seal the bare wood using a linseed oil-based paint or clear wood sealer.

A putty or caulking knife can be used to apply the traditional glazing putty. However, using a knife will give an easier application and a stronger seal. Select a putty specifically designed for glass windows as it has better adhesion and a longer life.

Apply a small amount of the putty to the inside edge of the frame where it meets the glass. Slide the window into frame so that the scribed line on the glass is aligned with edge of frame. Apply pressure on the glass to force the putty and glass to form an elongated seal. Smooth the compound using gloves and then remove any caulk or drips that were not properly applied before it dries.