• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace window pane Window Panes

A cracked window pane can be a source of frustration. It can also be a chance to upgrade your glass to energy efficient or insulated windows, and benefit from improved comfort, increased the value of resales and lower utility bills.

You can do it yourself for only a fraction of the cost it would cost to hire an expert. You only need the proper tools and a few minutes of your time.

Glass

If your single-pane windows are old, deteriorating or broken replacing them with modern insulated or tempered glass can improve energy efficiency and reduce noise while maintaining the historical integrity of older homes. The process of replacing a window pane is relatively easy and can be completed by anyone with basic hand tools. Alongside a upvc replacement window handles pane, the following components are required such as latex glazing putty; pliers, glazier's points and the use of a heat gun to warm the old putty, if needed. Before beginning, wear protective gloves and goggles since working with broken glass may cause injuries.

Begin by removing any broken pieces of glass. This is best accomplished with a pair of pliers, though using flathead screwdrivers can be effective in a pinch. Then, use a wooden chisel or putty knife remove the remaining old putty from the frame and sash. Take your time and work slowly and be careful not to break the existing window sash. This can be done best on a ladder, not the ground. Also, replace window pane ensure that someone lower to hold it steady.

After you have removed all the old putty, prepare the window frame to accommodate the new pane. Find the width and the height of the opening in the sash, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to the nearest hardware store or home center, and get a piece of stock glass cut to size. You can also cut the glass by yourself if you possess the appropriate tools.

After installing the glass, apply caulking on the edges. This will make the glass weatherproof. Install a glazier's point on both sides of the frame. This will help secure the pane. The points should not be so tight as to cause friction between the sash and the frame but they should not be too loose.

Before applying the putty make sure to knead it until it's soft and free of lumps. Cut it into pencil-sized pieces. Apply the first strip to the frame's corner. Work from one corner to the next, making sure it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular metal pieces that help secure the glass into the window frame without causing any damage to the fragile surface. It's easy to understand how to use this nefarious tool, and you'll save money on the cost of an expert installation.

After removing the old putty, glazier points, and any other remnants Clean the frame thoroughly using an utility knife. If needed, lightly sand the wood along the grooves of the rabbets to smooth rough spots. If you decide to sand the wood, be sure to protect it by using painter's tape to prevent accidental damage.

Write down the dimensions of the frame. Take these dimensions to a hardware store or home center and have the new pane cut smaller than the frame's opening. This will ensure a tight fit and will allow room for expansion and contraction.

Place the new pane into the frame and push it in place with your hand. Use the point of the chisel, or the back of the putty blade to tap the glaziers' points as illustrated in Figure 11. After you're done, the points should be flush with the top edge of the pane, and the shoulders of the points should be just below the rabbet's rim groove.

Apply a small amount of glazing compound over the edges of the new glass and in the rabbet grooves to seal and protect them. Allow it to dry and cure completely.

Install the new window sash when the glazing compound has dried. First, you need to coat the wood with an even layer of linseed. This will prevent the newly-created putty from drying out or cracking when it absorbs moisture. Apply this coat with a brush or the edge of your putty knife, then use the chisel or the back end from the putty knife to gently hammer the new sash and glazier's point into the rabbet grooves. Repeat this process in intervals of 10 inches all around the frame.

Putty

A baseball hit, a rock thrown in error, or a tree falling can cause a broken or cracked window. The majority of windows can be replaced easily by installing a new piece. The glass is held in place with small clips made of metal called a glazier's point and putty, also called glazing compound. Before installing a new pane, first take out the old one and clean up the area with a rag and a pull-type paint scraper or an abrasive wood chisel. Wear safety glasses and gloves while you do this work. You'll need a heating gun when the window is fixed into the frame.

If you're planning to reinstall your original sash, you must remove the mold that holds the old pane. Then, sand the sash to ensure it's smooth and ready to be re-caulked. After the sash has been re-installed then, apply a new caulk made of silicone around the glass to ensure it doesn't swell or fade in time.

Take the glazing points out of the rabbets and the grooves in the sash where the glass sits. If they're hard to chisel out, you can try holding a hand tool like a heat gun over them to soften them before you do. When using a heat tool, be careful to avoid damaging the sash or its railings.

Once the old glaze points and putty are removed, make a bed for the new pane. Roll a rope made of glazing compound between your fingers and make it about 1/2 inch thick. Then, press it into the rabbets in which the glass will be. The glass must rest against the putty on both sides. If necessary gently tap your glass into the rabbet using your thumb.

If the new pane has a crack you can fill it with a solvent-based glass glue or silicone caulk prior pressing it into the sash. If not, you'll have to putty over the crack to form an airtight seal and keep water out. After the putty has dried clean the oily film from the glass and allow it to dry completely before painting. Paint before the putty has dried completely. It won't form a good seal and may discolor or leak over time.

Paint

If you've experienced a broken window pane, then you may be concerned about the expense of a new one. But the truth is that replacing one glass pane does not have to break the bank If you can do it yourself. Even a double-paned window can be replaced at a fraction of the cost it costs an expert.

If you're working with large glass windows first ensure it is securely attached to the frame. With the right tools and techniques you can make this task relatively easy and speedy.

If you're ready to begin taking off the old window pane by prying out the glazing points made of metal that are connected to it. These are basically small metal triangles that act as "nails" that hold the window in in the wood frame. They are submerged beneath a layer of glazing putty that is then cured to form a solid, formed wedge that secures the window in place and hides the window's points.

After you have removed the old pane removed clean the surrounding frame and wood. Scrape away any old paint and sand down the rabbet grooves where the glazing points were. Sand them down to bare wooden surfaces, allowing you to paint the frames with the same shade. After sanding, apply a layer of flax oil on the wood that is not sanded down to prolong its life.

Then, take measurements of the dimensions of the window opening. You'll need to take vertical and horizontal measurements of the entire opening as well as the thickness of the old pane. To get the exact size of the new pane subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. Take these measurements to a hardware or home improvement store and have a piece cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.