• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Double Glazing Door Lock repairs double glazed windows

Has your uPVC window or door mechanism deteriorated? Perhaps the door or window handles aren't aligned properly or are hard to use.

It is essential that your double-glazed doors work smoothly, otherwise you'll lose energy and increase the chances of burglary. Owen the Locksmith will be able to fix your door lock at a reasonable cost.

Snapped Key

When a key snaps off in the lock, it can be extremely difficult. It could also be an issue for security, since the door might not lock and make you open to intrusion. There are a few quick fixes you can try to fix the problem and get your door working again.

Be calm. If you panic you could end up pushing the damaged key piece further into the lock.

Then, spray WD-40 or another penetrating oil into the lock to help the broken piece slide out more easily. You can also make use of a screwdriver to break up any pieces stuck that could be hindering the flow. If you're fortunate enough to have a little bit of the key left visible, you can make use of a paperclip or other metal object that is thin to grab it and then pull it out. Both of these methods work well, however, be cautious not to push the damaged piece of the key even further into the keyway.

Some paperclips have grooved edges that could work in a pinch as hook extractors and Jigsaw blades can also be used for this purpose. If you don't happen to have any of these items then you can bend a hook with needle-nosed pliers. Additionally, a pair of tweezers can be used to grasp and remove the remaining bit of the broken key.

If you can't get the broken piece of key out, try using a lock de-icer. This is usually available at most hardware stores, and it is used to freeze any moisture or ice that may be in the lock.

If none of these solutions seem to work, it may be time to consult a locksmith. The experts at Fitlocks can quickly solve problems with uPVC door mechanisms and locks, including snapped keys and broken handles. They can also modify your double glazing door mechanisms to make them easier to operate. You can book an appointment online for a double glazing repairs-glazing repair or contact us to discuss your requirements.

Broken Cylinder

A damaged cylinder could pose a serious security risk. It's a good thing that it's a simple repair for a professional locksmith to complete. To fix the cylinder, a locksmith will need to tap it. This can be accomplished with a hammer or other tool. The best method is to make use of a wire or a long match. The match or wire end near the keyway. The locksmith will strike the lock and break it open. This is better than using a hammer that could damage the lock.

Overheating is the main reason for cylinder heads to crack. This can happen when the cylinder block and cylinder head are made from different metals, such as cast iron and aluminum. When various metals are heated and cool at different rates, it could create hotspots locally that expand faster than the rest of the cylinder head, leading to cracks.

Corrosion is a different cause of cylinder fractures. When the cylinder head and the block of the cylinder are not properly maintained, it can cause corrosion or rust that could cause them to expand at a a higher rate than they ought to. Over time, this can also lead to cracks.

If your uPVC window or door lock is stiff or requires lots of pressure to turn, this can be the result of a number of things. A malfunctioning locking mechanism, misalignment, or a worn handle are common reasons for this issue.

It is a quick and inexpensive fix that most double glazing owners can do. A professional locksmith can usually fix this problem within one hour of arriving at the property. They can fix the locking mechanisms, or change the window handles and replace the gearboxes, depending on your particular requirements. A skilled locksmith will always be able to advise you of the most cost-effective solution for your home. They can even recommend upgrades to 3 Star security euro cylinders TS007 that add an extra layer of protection against burglars. It's a small price to pay for the peace-of-mind that comes from knowing that your uPVC door is secured.

Broken Handle

It's not a surprise that window handle locks could break. They are equipped with complex mechanisms that wear out over time. If yours breaks it's difficult to identify the cause of the issue and make sure you fix it properly.

If the issue is related to the locking mechanism inside or the latch, fixing your broken handle can improve your uPVC double glaze window repair (funny post) glazing door's security as well as help you stop the draughts. It is costly to repair or replace your handle incorrectly and it could also harm the frame and lock of your door.

With the window in the open position then loosen the screw that holds the handle by using the screwdriver. The screw should be located on the inside of the backplate, usually concealed by a screw cap for aesthetic purposes. It is not recommended to lose any internal components of the handle, such as the levers and plates on either side. It is best to keep them in the same order so you can re-install them when needed.

Then, rotate the handle to make it 90 degrees to the window frame and loosen the screw on the back of the handle which holds it to the internal spindle by using another screwdriver. Once the screw is released, you'll be in a position to pull the handle off and pull out the broken spindle. Replace it with a brand new one, ensuring it is the same length as the previous one (you can typically find these online or in hardware stores) and securely screw it into the correct position. Don't over tighten the screw as this could harm the handle as well as the window frame.

Close the handle and test it. It should operate smoothly, and you will be able open your window once again.

Make sure to check that your uPVC window is shut properly while you're working with the handle. If they're not then you may experience draughts and damp in your home, as and also affecting your home's energy efficiency. Core Sash Windows is a local window company that can alter the hinges of the frames of your windows to ensure that they close properly.

Broken Spindle

It is quite common that the spindle in a handle breaks rather than the handle itself. This is especially common with uPVC tilt-and-turn windows. These windows require a handle to operate an locking device within the window frame. The handle is connected to a rod in the centre that in turn activates mushroom-like locking cams, these lock into window frame keeps. If the dead latch mechanism fails to open when the handle is turned, it is likely that the spindle has been damaged This can be an extremely frustrating issue.

Luckily, there are ways to remedy this situation. A good locksmith can quickly and efficiently solve the issue. They will be able to remove the window handle using a tool that can remove the wheel part of the mechanism where the spindle is. This can be done without causing any damage to the handle or causing any other damage to the window frame.

Once the wheel is removed, the technician will examine the spindle to determine what has caused it to break. This involves disassembling the spindle and inspecting each component, noting any damage or excessive wear. This process is typically performed in a clean room by highly skilled technicians.

Then, clean the damaged spindle. This will remove any dirt or other debris that might be preventing it from working normally. The spindle may be replaced or repaired. If the technician is replacing the spindle he can use a dowel that is comparable in size to the original. He will then drill holes that are identical to both pieces. This will ensure that the new spindle has a precise fit with the handle.

If the spindle is damaged and cannot be repaired, it might require replacement completely. Home centers can sell generic replacements but if the window design is unique, you will need to contact an expert in cabinet making or woodworking who can replicate the exact piece. After the spindle is installed, it can be connected to the handle. The screw holes on the handle with the screws that are already in the frame. Once the handle is securely seated, you can operate your uPVC windows.